Send Feedback
Alpha Phi Omega
C.I.R.C.L.E. 5, Inc. - DX5APO
CIRCLE OF INTEGRATED RADIO COMMUNICATION LINK FOR EMERGENCY, INC.
144.820 MHz    7.045 MHz
Sign our Guestbook
HAM RADIO ONLINE TUTORIALS


MODULE V
  • Electron Theory and Atoms
  • Resistance
  • Resistors
  • Ohms Law
  • Current and Voltage
  • Voltage Dividers
  • Capacitance
  • Inductance
  • Reactance
  • Resonance and Impedance
  • Diodes
  • Transistors
  • "Q"
  • Radio Terminology A-L
  • Radio Terminology M-Z
  • Atttenuators
  • Chokes
  • Decibel & Toroids
  • Digital Basics
  • Power Supplies
  • Conclusion

  • FREE HAM RADIO E-TUTORIALS

    A beginner? Subscribe to our FREE Basic Ham Radio E-Tutorials and receive your editions of the Course at your e-mailbox Free of Charge.

    Please Enter Your Name:

    And Your E-Mail Address:

    HAM RADIO ONLINE QUIZ/TEST

    Preparing for the NTC Ham Radio Licensure Exams? Try the New Edition of our Online QuizTest for all classes of Amateurs!

    Go Ahead!
    ONLINE MORSE CODE QUIZ/TEST

    Want to test your speed in Morse Code? Try our online Morse Code Quiz/Test for Amateur Class A, B, and C!

    Go Ahead!

    CALL BOOK

    All Hams! Add Your Call Sign to our Call Book. Register Now!

    Sign Up!
    BULLETIN BOARD

    Post your announcements, invitations, ham activities for all the world to see! Or open a topic for discussion! And of course, have Fun!

    Go Ahead!
    PUBLIC PHOTO CENTER

    Upload your photos for public viewing! Ham radio activities and personal photos accepted!

    Go Ahead!
    GUEST MAP

    Pin your location on our Website Guest Map and leave your message!

    Go Ahead!
    MEMBERS!
     Update Your Record
     Upload Your Foto!
    RECOMMEND THIS SITE!
    Type In Your Name:

    Type In Your E-mail:

    Your Friend's E-mail:

    Your Comments:

    Receive copy: 

    Save Ham Radio!

    Vote For This Site!
    MODULE V - FUNDAMENTALS OF ELECTRONICS
    RESISTANCE

    In the topic current we learnt that certain materials such as copper have many free electrons. Other materials have fewer free electrons and substances such as glass, rubber, mica have practically no free electron movement therefore making good insulators. Between the extremes of good conductors such as silver, copper and good insulators such as glass and rubber lay other conductors of reduced conducting ability, they "resist" the flow of electrons hence the term resistance.

    The specific resistance of a conductor is the number of ohms in a 1' (305mm) long 0.001" dia round wire of that material.

    Some examples on that basis are Silver = 9.75 ohms, Copper = 10.55 ohms, Nickel = 53.0 ohms and Nichrome = 660 ohms

    From this information we can deduce that for a voltage applied to a piece of Nichrome wire , only around 10.55 / 660 = 0.016 of the amount of current will flow as opposed to the the current flowing in the same size copper wire.

    The unit of resistance is the ohm and 1 ohm is considered the resistance of round copper wire, 0.001" diameter, 0.88" (22.35 mm) long at 32 deg F (0 deg C).

    RESISTANCE IN SERIES AND PARALLEL

    It follows if two such pieces of wire were connected end to end (in series) then the resistance would be doubled, on the other hand if they were placed side by side (in parallel) then the resistance would be halved!

    This is a most important lesson about resistance. Resistors in series add together as R1 + R2 + R3 + ..... While resistors in parallel reduce by 1 / (1 / R1 + 1 / R2 + 1 / R3 + .....)

    Consider three resistors of 10, 22, and 47 ohms respectively. Added in series we get 10 + 22 + 47 = 79 ohms. While in parallel we would get 1 / (1 / 10 + 1 / 22 + 1 / 47) = 5.997 ohms.

    RESISTANCE AND POWER

    Next we need to consider the power handling capability of our resistors. Resistors which are deliberately designed to handle and radiate large amounts of power are electric cooktops, ovens, radiators, electric jugs and toasters. These are all made to take advantage of power handling capabilities of certain materials.

    From our topic on ohms law we learnt that P = I * I * R that is, power equals the current squared times the resistance. Consider our example above of the three resistors in series providing a total resistance of 79 ohms. If these resistors were placed across a 24 volt power supply then the amount of current flowing, from ohms law, is I = E / R = 24 / 79 = 0.304 amperes.

    Using any of our power formulas we determine that 0.304 amperes flowing through our 79 ohm resistance dissipates a combined 7.3 watts of power! Worse, because our resistors are of unequal value the power distribution will be unequal with the greater dissipation in the largest resistor.

    It follows as a fundamental rule in using resistors in electronic circuits that the resistor must be able to comfortably handle the power it will dissipate. A rule of thumb is to use a wattage rating of at least twice the expected dissipation.

    Common resistors in use in electronics today come in power ratings of 0.25W, 0.5W, 1W and 5W. Other special types are available to order. Because of precision manufacturing processes it is possible to obtain resistors in the lower wattage ratings which are quite close in tolerance of their designated values. Typical of this type are the .25W range which exhibit a tolerance of plus / minus 2% of the value.

    Resistors come in a range of values but the two most common are the E12 and E24 series. The E12 series comes in twelve vaues for every decade. The E24 series comes in twent four vales per decade.

    E12 series - 10, 12, 15, 18, 22, 27, 33, 39, 47, 56, 68, 82

    E24 series - 10, 11, 12, 13, 15, 16, 18, 20, 22, 24, 27, 30, 33, 36, 39, 43, 47, 51, 56, 62, 68, 72, 82, 91

    You will notice with the E12 values that each succeeding value falls within the plus / minus 10% of the previous values. This stems from the real old days when resistances were stated as within 20% tolerance (accuracy). Later values of plus / minus 5% tolerance led to the E24 range of resistance. Quite common today are 2% tolerance metal films types but for general purpose use we tend to stick to E12 values of resistance in either 1%, 2% or 5% tolerance.

    Cost is the determining factor and many retailers now stock the 2% range of resistance as a standard to minimise stocking levels and also at reasonably low cost.

    As examples of say the "22" types (red - red) from the E12 series we get 0.22, 2.2, 22, 220, 2,200, 22,000, 220,000 and 2,200,000 or eight decades of resistors.

    RESISTANCE COLOUR CHART CODES

    Here in this large colour chart is the resistance colour code - learn the sequence forever -

    BLACK, BROWN, RED, ORANGE, YELLOW, GREEN, BLUE, PURPLE, SILVER, WHITE

    We have accomodated two current colour banding of resistances - four band and five band resistance colour code. It should be pretty self explanatory we hope.

    resistance color chart

    The five band code is more likely to be associated with the more precision 1% and 2% types. Your "garden variety" 5% general purpose types will be four band resistance codes. Free download Color Code Convertor Program.

    Back to Top


    Visit Rey's WebCreations