- Although the CIC GPSR-A differs from it in many respects, you may find the Z3801 User Manual useful as a broad introduction to the unit and its functionality. Unfortunately we (currently) have no manual available for the CIC GPSR-A units.
- In some respects the CIC GPSR-A is the 'poor relation' to the HP Z3815A, because of the limited command set, and other problems in the firmware (see later); but from a functional point of view, the unit works well, draws less power than the HP Z3815A, and arguably has a better reference. In general the units are also newer than available HP units. That said, if you have a choice, for Amateur Radio applications the HP is a better unit to own. As a stand-alone unit where user interaction is minimal (such as in a lab reference) the CIC is a good choice.
- The rear panel connections are shown in great detail in the Backplane Drawing. If you spot any errors, let us know.
(The drawing is based on the HP Z3815A, but the pinouts are the same, even though the numbering is reversed - after all, the units are functionally interchangeable).- The CIC can be operated lying flat or standing up, provided there is no restriction to convection air flow. Power consumption is 30% less than the HP unit. Ideally the unit should be mounted vertically, arranged so that the bottom is clear of the supporting surface by 10mm or more.
- It has been discovered that sometimes from cold the unit warms up and does everything right, but does not obtain a fix, or lock the oscillators. It is believed that this is because the default position in the GPS receiver is on the other side of the world. If this happens, and you'll see it live if you use the GPSRSTAT software, press the GPSR RESET button and all should be well within a couple of minutes.
- These pages are very much a work-in-progress. Due to complete lack of official documentation, there could be (and are sure to be) any number of errors and areas of misunderstanding. If you have any useful input, we'd be very pleased to hear about it, and include it on these pages. Remember - you saw it here first! The world's one and only CIC GPSR-A web page!
- Comments, useful input and so on to the author please.
Since the rear coax connector block is an odd type, the simplest approach is to open the lid and replace the short coax cable tail between the GPS module and the main board. Replace this with a 150mm long tail with SMB on one end (to suit the GPS module) and SMA or BNC panel mount on the other (to suit the antenna).Then drill a hole in the back panel to mount the new connector. See the picture for an example. The gold connector on the rear panel is an SMA female panel mount.
You can tell when the antenna is drawing current as the +5V on the cable will drop by a few mV from the open-circuit condition.
Using a single-row or dual row 2.54mm spaced gold flashed pin strip, plug into the rear multi-way block connector, row A, pins 65 downwards (the ones nearest the white coax block). Check with the Backplane Drawing. Solder 1mm or heavier flexible wires about 300mm long to the appropriate pins. You want to connect to one or more pins labelled 'DC In (A)' for one wire, and one or more pins labelled 'DC In (B)' for the other. See the picture below.
Although the left wire is red and the right one black, the polarity of the power supply is unimportant. A double row pin strip is suggested, as these hold in place better than a single row strip (row B is 0V at this point). A length 10 pins long will suffice.
NOTE:
It has been found (the hard way) that plugging the power into the wrong row on the connector does serious damage to the unit!At the other end of the power leads solder a connector to suit your power supply. You need a very reliable connector with no possibility of erratic connection. Any 20W power supply from 24 to 50V will do - the author used a 24V 2A switch-mode consumer type made in Asia. A regulated supply will be best, but 30V to 50V DC unregulated will work if there is sufficient filtering for less than 1V ripple (at least 4700µF).
Another very tidy solution is to make use of the footprint for connector P6 (not fitted). This is situated just behind the heatsinks near the top edge on the top side of the board. The pins are connected in parallel with the backplane power pins: 1 and 2 are DC In(A), while pins 3 and 4 are DC In(B). Run a pair of wires around the top edge of the case from this connector footprint to a panel mount coaxial DC connector on the rear panel. An example is shown in the picture of the antenna connector above. The next picture shows connector P6 on the left, with wires attached.
Click on picture for full size viewIf your power supply voltage is always above 30V, you can easily arrange an automatic battery backup supply, by using two 7AH SLA batteries in series, coupled to the DC supply by a 5A isolating diode such as 1N5402. Make sure you get the polarity correct! You will need to arrange an independent means of charging the batteries. The ripple on the power supply must not dip below the battery voltage.
A very convenient and tidy adaptation can be made to the unit by adding a row of connectors to the back panel. See the photograph below.
,br>Click on picture for full size view
The three left connectors are isolated BNC types for (left to right) 1PPS, 19.6608MHz and 10MHz sine wave signal. The first two are picked up from nearby points on the circuit board via 100Ω resistors, while the 10MHz is connected in parallel with the outputs on the white block, using a short length of coax cable.
The other two connectors (to the right) are an SMA for the antenna and power connector for the DC power. There is sufficient space for two further outputs, such as 1.544MHz or 4.096MHz (from the backplane). Because there is an internal 5V CMOS level 10MHz signal available, it would not be difficult to add a small divider board inside (equipped for example with a 74HC390), in order to provide 1MHz and 100kHz outputs.
- 10MHz
- Sinewave, 5V p-p open circuit, 2.5V p-p into 75Ω, 2V p-p into 50Ω. Output impedance 75Ω. Three outputs available from white connector block (connect to back of connector). Output is enabled only when the GPSR is locked!
- 19.6608MHz
- Square wave, 0 - 2V open circuit with some HF ringing. 0 - 1V into 50Ω, with no ringing. Output available from circuit board - add 100Ω series resistor to rear connector.
- 1PPS
- Pulse, 25us duration, CMOS level 0 - 4V open circuit. Output available from circuit board - add 100Ω series resistor to rear connector.
- Backplane Signals
- Signals 19.6608MHz, 4.096MHz, 1.544MHz are available from the backplane connector in balanced pseudo-ECL form once the GPSR is locked. These signals can be terminated in 50Ω. Can be used with an RS422 line receiver.
When you first power up, check the supply voltage, check that there is +5V on the antenna connector, and check that some of the LEDs on the panel are on. Close (upwards) the locking switch latch at the bottom of the front panel. This doesn't act as a power switch (there is no power switch), but leaving it open puts the unit in 'Block' mode and may disable some features (still to be determined).First check out the comms using a Terminal program (even Hyperterminal if you must!) set for 19200-N-8-1. (See next section for comm port connections). Press ENTER a few times - you should see the prompt 'SCPI >' appear each time. Type ':SYST:STAT?' and check the returning message for any alarms, for example GPS antenna faults. Use GPSRSTAT software for continuous monitoring.
At first the 'Unlock' and some other lights will be on. Once the unit has been running for 30 minutes or so, the 'GPS Available' LED should come on, soon followed by the ''Status Active' LED. You're in business!
It may take some time to achieve GPS and Lock when you first power up, because the last known position and time will be wrong. The unit will first have to search for a satellite (with no good ephemeris, almanac, time, position or even satellite frequency table, this takes some time), and once it has found one, it then needs to collect the time, ephemeris and almanac and work out the position. To achieve a very accurate position necessary for providing very accurate time, the unit goes into 'site survey' mode automatically for 24 hours. In this time the reference frequencies will be good, but not stunning. After the survey is complete, the unit switches to 'position hold' mode, and the results will be superb.
If you peer inside the unit through the ventilating holes, you will see a green LED which flashes on or off every other second. You can also monitor the survey and lock status using the front panel RS-232 port and GPSRSTAT software.
The CIC unit operates at 19200-N-8-1, but is not able to handle full-speed data from a program, only hand-typed text. (Hint - when writing programs, allow 10ms between transmitted characters). The CIC unit has only a limited subset of the Z3815A SCPI protocol, and for all these reasons, commercial Z3801A software does not work with these units. The known commands (and their responses) are:
COMMAND FUNCTION TYPICAL CIC GPSR-A RESPONSE *CLS Clear error prompt scpi> *IDN? Request ID CHONGHO I&C Co,.LTD. GPSR-000000 ver3.03 2001/04/12 :DIAG:LOG:READ? Request latest log item Timestamp and latest error event described :DIAG:LOG:READ:ALL? Request error log List of all errors since log cleared :DIAG:LOG:CLE Clear error log Time stamp and clear event log entry :DIAG:ROSC:EFC:REL? Request Relative EFC voltage +1.69286E+001 :DIAG:ROSC:EFC:ABS? Request Absolute EFC voltage -30684 :GPS:POS? Request current position S,+37,+8,+1.39180E+001,E,+174,+54,+1.38200E+001,+8.74300E+001 :GPS:POS:SURV ONCE Force into survey mode :GPS:POS:SURV:PROG? Request survey progress 45% :GPS:POS:SURV:STATE? Request survey state :GPS:REF:ADEL nn NS Set antenna delay to nn :GPS:REF:ADEL? Request antenna delay +10 :GPS:SAT:TRAC:EMAN? Request GPS elevation mask angle +0.00000E+000 :PTIM:LEAP:ACC? Request UTC leap secs +14 :PTIM:DATE? Request GPS date +year,+month,+day :PTIM:TIME? Request GPS time +hours,+minutes,+seconds :SYNC:HOLD:INIT Forces manual holdover :SYNC:HOLD:REC:INIT Starts manual holdover recovery :SYNC:TINT? Request 1pps TI No response! :SYST:ERR? Describes syntax error, e.g. - 113, Indefined header :SYST:PRES @@@ Reset to factory settings Reset message, plus string of HEX data repeated every few minutes :SYST:STAT? Request Status message Full screen message (about 1500 characters) @@@ Note: Do not use :SYST:PRES unless absolutely necessary. You will lose all the system preset values, including the 'Smart Clock' parameters, with the result that the system will take some days to return to peak performance, and various alarms will appear. Cycling the power is preferable!
The front panel diagnostics port is wired as an RS232 DTE device (same as a PC or terminal), but unfortunately has the connector normally used by a DCE (such as a modem). You need either to make a special cable to connect 2, 3 and 5 at one end to 3,2 and 5 at the other (both DB9M connectors), or use a 'Null Modem' cable together with a male-male sex changer, or a 'Modem' cable together with a 'Null Modem' male-female adaptor.
Run the GPSRSTAT software, or simply send commands from the terminal - although this quickly becomes tedious! The GPSRSTAT program requests the status display automatically, and with correctly spaced characters to simulate hand typing. The display shows just about everything you would want to know from both the GPS receiver and the Disciplined Oscillator system, but unfortunately no graphing of data is possible.
The serial comms connection is not required for normal use - only for those interested in seeing how good the performance is, or for checking for problems.
Note that the time displayed via the front panel serial port is GPS TIME. This is currently 14 seconds ahead of UTC, since UTC leap seconds are not accumulated in GPS time. It is not known at present if the units can be switched to show UTC time.
The Motorola GPS module in the unit has yet to be investigated in depth, but is believed to be an 8 channel Oncore. However, the serial data can be accessed using a simple level converter. There are numerous problems in the CIC firmware related to interrogating the GPS receiver. Every second the GPSR receives the '@@Ea' message, which contains basic time, navigation and satellite status information, sufficient to operate an excellent GPSDO, or to drive an external display showing time, position etc.However, the '@@Bb' message, important for reporting the satellite constellation information, is received only soon after reset, and never again. Hence the unit cannot correctly report satellite AZ/EL information, and tends also to keep satellites in the 'in view' list long after they are below the horizon. The only satellite information in the Status message that is valid is the number of satellites in the fix, the satellite PRN and C/N (ID number and signal strength).
Serious problems have been discovered in the CIC GPSR-A satellite reports (in the Status message). Essentially, the Azimuth, Elevation, and list of satellites in view are complete fiction! The ID of satellites in the fix, and the C/N ratio of these satellites are correct.ZL2AFP Windows software is now available for the CIC GPSR-A. Everything works correctly except the satellite constellation and antenna plot (this information is not correctly provided by the CIC).