This page is dedicated to a relatively rare and largely unknown GPS Disciplined Oscillator (GPSDO) module, previously manufactured by Hewlett Packard (now Agilent) and later by Symmetricomm. At present not a great deal is known about this unit. The web page has been put together to share what little we do know about this very nice little GPSDO. The unit has been found in Australia in CDMA base stations of Korean manufacture. (See picture on right). The photos on this page are courtesy of Kit VK2LL.The unit was originally designed by HP. It included the amazing HP E1938A 'hockey puck' oscillator in earliest versions. This oscillator was one of the first single-oven SC-cut OCXOs to challenge the performance of the double oven OCXOs generally used in high performance applications. Unfortunately after a modest production run, the E1938A went out of production. Rick Karlquist N6RK was on the E1938A design team, but can shed no further light on the Z3815 product.
The design was soon adapted to several other oscillators, including for example the Milliren 260 double-oven unit seen on the main board view and in the photograph below. Clearly this oven adaptor was developed by Symmetricom to fit where the E1938A used to go (note the connector on the right). The original oscillator was a 10MHz unit, and while the main output of the later units remain as before, some apparently use a 5MHz oscillator and doubler in the adaptor design. The newer board design again uses a 10MHz OCXO. So far versions have been found with HP, Milliren, C-MAC and CMC oscillators. There are at least two board layouts, and at least two software versions.
The Symmetricom adaptor board with Milliren MTI-260 double oven OCXO
Click on picture for a full-size view
No specifications for this unit have been found (yet). All we have is a rough description on a Korean web page:"The Z3815A was designed to supply synchronous clocks to the backplane of a 2G CDMA Base Station Transceiver System (BTS). It uses HP Smart Clock Technology used where very accurate timing is required, such as in E1/T1 telecom networks. It provides accurate time and position information, and has front panel LED indications to confirm various operational conditions. It provides the strict holdover requirements for a 2G system, 8us/24 hours."We do know that the unit is powered from 20V to 56V DC (either polarity), and draws 850mA cold, 550mA at 48V when warmed up. There is some variation, depending on the oscillator type fitted). The unit warms up and is fully operational within 15 minutes, or five minutes from a warm start. The 1pps output is 20us wide, and outputs are provided for 10MHz, 8.388688MHz (223) and 19.6608MHz (216 x 300). On some units the outputs do not appear until the GPSDO is locked. Some units have other outputs. It would appear that the outputs are under software control.
The backplane outputs are in general balanced pseudo-ECL outputs (current drive, similar to RS422). The driver chips have a common enable. The 10MHz output is unbalanced and comes from the coaxial connector block at the top, which is also where the GPS antenna enters. Some arrangement will need to be made to connect to these points, as the coaxial connector block mating connector is a special one, and not available. Other signals are available scattered around the main board. Many have the footprint suitable for a PCB-mount SMA or MSX connector.
The unit is about 300mm high, 300mm deep and 100mm high. It weighs about 1kg. The full length of the back panel is taken up with the coax connector block and backplane connectors.
There is an RS232 diagnostic interface on the front panel. It is also known that the unit uses an SCPI Protocol (Standard Commands for Programmable Instruments). In the older versions it is identical or closely similar to SCPI V1994.0 used by the HP Z3801, and detailed in the Z3801 User Manual . (The SCPI is commonly known for want of a better name as the :SYS:STAT protocol, from the most widely used command). The Z815 units also identify themselves, betraying their origin without any doubt, by responding to the *IDN? query as:HEWLETT-PACKARD,Z3815A,3704A00427,U-4010.0-AThe extensive command set allows just about every parameter within the unit to be interrogated. Some Z3801 software may work with these units.
SATSTAT (download archive from Symmetricom)
Older models of Z3815 are known to respond to this simple program. A sample :SYS:STAT response this program generates is shown below.
![]()
Z3801A software by ZL1BPU (download archive, 102kb)
Three programs are included:
These programs use a common setup file, Z.set, which must be edited by the user to reflect the correct COM port and baud rate for the Z3801. The programs are compiled DOS, and will work in a DOS box from WIN98 to WIN XP, although you may find that ZEFC4 needs to operate full screen to display the graphics (graphics card dependent). These programs operate well on a 233MHz Pentium computer. For some Z3815 models you may have to use 9600 bps rather than 19200 bps.
- Zclock1 displays the time and paramaters associated with the Z3801 time message.
- Zsimple1 requests the status page, refreshing at a user selected rate (much like SATSTAT).
- Zefc4 is a complex monitor program which interrogates and plots the Z3801 reference time offset, the EFC control voltage, and the GPS satellite fix status (number of satellites used and in view). It also displays the time.
The plan is to add further programs specifically for the Z3815 family when more is known about the communications protocol.
Older main board view
More recent main board view
Symmetricomm MTI 260 adaptor board detail
Rear view showing manufacturer's labels and connectors
Circuit board back side (magnify pic and note all the silk screen annotations)