Commissioning

the

HP Z3815A GPS DISCIPLINED REFERENCE


Initial Hints

  • Although the Z3815A differs from it in many respects, you may find the Z3801 User Manual a useful introduction to the unit. Unfortunately we (currently) have no manual available for the HP Z3815A or CIC units.
  • The rear panel connections are shown in great detail in the Backplane Drawing. If you spot any errors, let us know.
  • It's not a good idea to operate the unit for long lying flat or standing up on the lower ventilating edge. Both positions will seriously affect the convection air flow. Ideally the unit should be mounted so that the bottom is clear of the supporting surface by 10mm or more. In normal use the unit is force cooled by a cabinet fan system, so arranging a simple mounting plinth with an internal fan forcing air into the lower vents would be a good idea.
  • It has been discovered that sometimes from cold the unit warms up and does everything right, but does not obtain a fix, or lock the oscillators. It is believed that this is because the default position in the GPS receiver is on the other side of the world. If this happens, and you'll see it live if you use the Z3815A5 software, press the GPSR RESET button and all should be well within a couple of minutes. If you're watching the GPS data (see below) you'll suddenly see the satellite constellation rotate and come right.
  • These pages are very much a work-in-progress. Due to complete lack of official documentation, there could be (and are sure to be) any number of errors and areas of misunderstanding. If you have any useful input, we'd be very pleased to hear about it, and include it on these pages. Remember - you saw it here first! The world's one and only HP Z3815A web page!
  • The relationship between ABSOLUTE EFC and RELATIVE EFC is as follows:
    ABS = REL x 5242.88 + 524288
    Thus the ABSOLUTE range is 0 to 1048585 (0xF FFFF, 20 bit) while the RELATIVE range is -100 to +100. The operating centre EFC voltage is thus represented by ABS = 524288 or REL = 0. Make sense? Bear in mind though that the REL value is expressed in floating point, while the ABS is expressed as an unsigned integer.

    This is the same arrangement as the Z3801A, but NOT the same as the CIC unit, for which the relationship has yet to be worked out.

  • Comments, useful input and so on to the author please.

GPS Antenna

Since the rear coax connector block is an odd type, the simplest approach is to fit a short coax cable tail to the rear of the unit. Use very thin high quality 50 Ω cable, and keep the connections VERY short. The author used a 300mm length of Belden 83265 Teflon/Silver cable, about 2mm overall diameter.


Showing how to connect the antenna cable

As shown in the photograph, you should thread the cable through the nearby hole in the circuit board, which acts as a simple strain relief to prevent the fragile cable working and breaking. A blob of hot-melt glue placed in the hole after the cable is soldered in place would be a good idea. The cable inner connects to the outer pin in the second row (the first row with only two pins). The cable screen connects to the outer pins in the first and third rows (with three pins).

At the other end of the cable, fit a suitable female connector to match your GPS antenna (SMA, MSX, BNC etc). The cable provides +5V to the antenna to power the LNA, so you must use a 5V active antenna. (Make sure you don't short the antenna!) A simple automotive magnetic mount patch antenna will suffice, provided it is mounted well in the clear.

You could replace the internal GPS antenna cable, as described for the CIC GPSR-A unit, but you may have trouble finding a suitable tiny connector for the GPS module.

You can tell when the antenna is drawing current as the +5V on the cable will drop by a few mV from the open-circuit condition.

Power Supply

Using a single-row or dual row 2.54mm spaced gold flashed pin strip, plug into the rear multi-way block connector, row A, pins 65 downwards (the ones nearest the white coax block). Check with the Backplane Drawing. Solder 1mm or heavier flexible wires about 300mm long to the appropriate pins. You want to connect to one or more pins labelled 'DC In (A)' for one wire, and one or more pins labelled 'DC In (B)' for the other. See picture on right.

Although the left wire is red and the right one black, the polarity of the power supply is unimportant. A double row pin strip is suggested, as these hold in place better than a single row strip (row B is 0V at this point). A length 10 pins long will suffice.

At the other end of the power leads solder a connector to suit your power supply. You need a very reliable connector with no possibility of erratic connection. Any 20W power supply from 24 to 50V will do - the author used a 24V 2A switch-mode consumer type made in Asia. A regulated supply will be best, but 30V to 50V DC unregulated will work if there is sufficient filtering for less than 1V ripple (at least 4700µF).

See the CIC commissioning page for hints about rear panel connectors.

If your power supply voltage is always above 30V, you can easily arrange an automatic battery backup supply, by using two 7AH SLA batteries in series, coupled to the DC supply by a 5A isolating diode such as 1N5402. Make sure you get the polarity correct! You will need to arrange an independent means of charging the batteries. The ripple on the power supply must not dip below the battery voltage.

Firing Up

When you first power up, check the supply voltage, check that there is +5V on the antenna connector, and check that some of the LEDs on the panel are on. Close (upwards) the locking switch latch at the bottom of the front panel. This doesn't act as a power switch (there is no power switch), but leaving it open puts the unit in 'Block' mode and may disable some features (still to be determined).

First check out the comms using a Terminal program (even Hyperterminal if you must!) set for 9600-N-8-1. (See next section for comm port connections). Press ENTER a few times - you should see the prompt 'SCPI >' appear each time. Type ':SYST:STAT?' and check the returning message for any alarms, for example GPS antenna faults.

At first the 'Unlock' and some other lights will be on. Once the unit has been running for 30 minutes or so, the 'GPS Available' LED should come on, soon followed by the ''Status Active' LED. You're in business!

It may take some time to achieve GPS and Lock when you first power up, because the last known position and time will be wrong. The unit will first have to search for a satellite (with no good ephemeris, almanac, time, position or even satellite frequency table), and once it has found one, it then needs to collect the time, ephemeris and almanac and work out the position. To achieve a very accurate position necessary for providing very accurate time, the unit goes into 'site survey' mode automatically for 24 hours. In this time the reference frequencies will be good, but not stunning. After the survey is complete, the unit switches to 'position hold' mode, and the results will be superb.

If you peer inside the unit through the bottom ventilating holes, you will see three green LEDs. One is on all the time, another (on the E1938A) flashes every second, and another on the main board flashes on or off every other second. You can also monitor the survey and lock status using the front panel RS-232 port and suitable software.

Serial Comms

The HP Z3815A operates at 9600-N-8-1. The Z3815A has a very similar protocol to the Z3801A, which is well documented. It operates with the Symmetricom SatStat software, but we know that the behaviour does differ a little from the Z3801A in the following respects:
  • The comms includes an echo to all commands (not known how to turn this off).
  • The prompt behaviour is slightly different.
  • The time code format defaults to Mode 1 (hexadecimal), rather than Mode 2 (decimal) as in the Z3801A. The mode can be switched with the ':PTIM:TCOD:FORM F2' command.

The comms port is wired as an RS232 DTE device (same as a PC or terminal), but unfortunately has the connector normally used by a DCE (such as a modem). You need either to make a special cable to connect 2, 3 and 5 at one end to 3,2 and 5 at the other (both DB9M connectors), or use a 'Null Modem' cable together with a male-male sex changer, or a 'Modem' cable together with a 'Null Modem' male-female adaptor.

Run either the SatStat software, the ZL1BPU Z3815A software, or simply send commands from the terminal - although this quickly becomes tedious! The ZL1BPU Z3815A5 program sends commands automatically, looking for the number of satellites in range, the number of satellites tracked, the EFC control voltage, the 1PPS timing error, the Holdover status, the date and the time. The EFC, 1PPS and satellite info are plotted graphically.

The serial comms connection is not required for normal use - only for those interested in seeing how good the performance is, or for checking for problems.

Note that the time displayed via the front panel serial port is GPS TIME. This is currently 14 seconds ahead of UTC, since UTC leap seconds are not accumulated in GPS time. It is not known at present if the units can be switched to show UTC time.

GPS Comms

The Furuno GPS module in the HP Z3815A also operates at 9600-N-8-1. However, the signal isn't available to the outside world. The GPS header on the main circuit board is a 7-pin connector, P9. There is reasonable access to it on the back of the board. Pin 1 is the pin nearest the centre of the board. The connections from the GPS module are:
  1. 1PPS 50% duty (brown)
  2. GPS TXD, CMOS level (purple)
  3. 1PPS +ve pulse (orange)
  4. 0V common (green)
  5. Purpose unknown (blue)
  6. +5V (yellow)
  7. +5V (red)
If you connect a PNP transistor inverter to this connector (see below), you can have RS232 level data out to your PC or other application! The communications is in NMEA format, and sends the $GPGGA, $GPGSA, $GPGSV standard messages and two $PFEC proprietary sentences. The fix data can be easily monitored with a standard PC package such as VisualGPS.


A suitable RS232 interface for the GPS unit

Build up the little circuit above on a scrap of Veroboard. Mount the RS232 connector (DB9-M) on the end of the board and connect it to the three points on the right, as shown. Connect three thin flexible wires about 300mm long to the left side of the circuit. With the power OFF, take the bottom cover off the unit and locate the pins of P9. Solder the three wires to the appropriate points. When replacing the cover, run the wires out the bottom corner of the cover, making sure it isn't pinched by the cover. Use a small cable tie or nylon line to tether the cable to the nearby PCB hole. The RS232 interface allows you to monitor the GPS, but not talk to it. The receive data line is only used to provide -9V to power the transmit data line.

You can use the FURUNO software (see previous page) to monitor the data. If anyone finds more detailed information about the $PFEC commands than is in the manual, let us know!

LATEST NEWS:

New Windows™ display and plotting software for the HP Z3815A GPSR is now available! See the software page.