5-BTV HUSTLER 80-10m Vertical 1kW * 5 Bands * Coverage 80-10m * Bandwidth Full * SWR 1.15:1 * Power 1kW * Traps 25.4mm formers * Tubing 31.75mm * Bracket size 44.45mm * Height 7.64m * Weight 7.7kg * Wind (112kph) 13kg -Radials provided by user, can be ground mounted. Exclusive trap design makes Hustler traps ultra stable and dependable. With Hustler verticals, you can not only adjust frequency by tubing length, you can actually tune the traps for up to 2MHz shift. Large diameter tubing gives full bandwidth on 10m - 40m with VSWR typically better than 1.6:1 at band edges. On 80m you will achieve around 80kHz bandwidth. Absence of tapered tubing makes this antenna really rigid and the 0.315in base tube wall adds to the rigidity. Longer than comparable verticals, these antennas are really efficient. As Hustler says, these antennas offer solid signals, solid construction and solid value.

6-BTV HUSTLER 80-10m Vertical 1kW * 6 Bands: 10, 15, 20, 30, 40, 80m * VSWR 1.6:1 or better 10-40m * Bandwidth up to 100kHz 80m * Power: 1kW * Feed: 50 Ohms * Solid 25.4mm traps * Feed with any length 50 Ohm coax * Heavy duty aluminium mounting bracket * Solid 25.4mm (1in) fibreglass trap formers * Use as ground mount with or without radials * Use with radials on elevated mount * Size: 7.3m (24ft) * Weight: 7.5kg

A quality 6-band antenna from Hustler. Will easily handle full legal limit of power on SSB and CW. Built to last, uses thick walled heavy duty aluminium throughout its length and has an extra heavy duty aluminium bracket for mounting. Its uniquely designed traps offer the lowest loss possible and can be further fined tuned for best SWR if required. With a vertical height of only 7.3m it can be safely mounted where other verticals cannot. Radials are optional if antenna mounted at ground level, but are required if an elevated mount is used. Performance is as solid as its construction.

AV-12AVQ HY-GAIN 10-15-20m Vertical 1500W * Bands: 20, 15, 10m * Power: 1500W PEP * Gain: 3dBi nominal * VSWR: < 1.5:1 typical * Vertical angle: 16 degs * Horizontal angle: 360 degs * Connector: SO-239Mast size: 38.1-41.275mm * Wind survival: 129 kph * Height: 4.1m * Weight: 4kg NOTE: The 12AVQ and 14AVQ are designed to be ground mounted or elevated with radials. A completely self-supporting triband vertical antenna. It  delivers exceptionally low angle radiation with 1.5:1 VSWR or less on all three bands. Includes all stainless steel hardware and SO-239 input connector.

AV-14AVQ 10-15-20-40m Vertical 1500W * Bands: 40, 20, 15, 10m * Power: 1500W PEP * Gain: 3dBi nominal * VSWR: < 1.5:1 typical * Vertical angle: 16 degs * Horizontal angle: 360 degs * Connector: SO-239 * Mast size: 38.1-41.275mm * Wind survival: 129 kph * Height: 5.5m * Weight: 4kg NOTE: The 12AVQ and 14AVQ are designed to be ground mounted or elevated with radials.

A self-supporting, automatic band switching vertical that delivers outstanding performance with exceptional L/C ratio and a very low angle of radiation pattern. Includes all stainless steel hardware and SO-239 input connector.

AV-620 Hy-Gain Patriot Vertical HF Antenna * Bands: 20, 17, 15, 12, 10, 6m * Power: 1.5kW * Gain: 3dBi nominal * Vertical angle: 17 degs * 2:1 SWR Bandwidth 20m 500kHz, 17m 500kHz, 15m 500kHz, 12m 500kHz, 10m 1.5MHz, 6m 3MHz * VSWR: < 1.5:1 typical * Wind survival: 127 KPH * Wind surface area: 0.22m2 * Height: 7.01m * Weight:5.44kg

The AV-620 covers 6x HF bands, handles 1500Won all bands except reduced to 500W on 6m, requires no traps, guy wires, radials or ground. It has an extremely low angle of radiation (17 degrees) ideal for working DX. Band selection is fully automatic and the antenna’s extra wide bandwidth covers all bands with low SWR. The AV-620 uses full-size quarter wave stubs for 6, 10, 12, 15 and 17m and linear loading for 20m. Robustly constructed the AV-620 sleek low-profile design is built to survive 127 KPH winds. It is easy to put up and requires only a small area, ideal for those small gardens.

AV-640 Hy-Gain Patriot Vertical HF Antenna * Bands: 40, 30, 20, 17, 15, 12, 10, 6m * Power: 1.5kW * Gain: 3dBi nominal * Vertical angle: 16 degs * 2:1 SWR Bandwidth: 40m 150kHz, 30m 175kHz, 20m 500kHz, 17m 500kHz, 15m 500kHz, 12m 500kHz, 10m 1.5MHz, 6m 1.5MHz * VSWR: < 1.5:1 typical * Wind survival: 127 KPH * Wind surface area: 0.22m2 * Height:7.87m * Weight: 9.9kg

The AV-640 covers 8x HF bands, handles 1500W all bands except 6m reduced to 300W, requires no traps, guy wires, radials or ground. It has an extremely low angle of radiation (16 degrees) ideal for working DX. Band selection is fully automatic and the antenna’s extra wide bandwidth covers all bands with low SWR. Robustly constructed the AV-640 sleek low-profile design is built to survive 127 KPH winds. It is easy to put up and requires only a small area, ideal for those small gardens

CP-6 Diamond Vertical HF Antenna * Bands: 3.5 -50MHz (CP6) * Power: 200W * VSWR: Better than 1.5:1 * Socket: SO-239 * Height: 4.6m * Radials: 1.8m adjustable .The CP6 covers six popular HF bands, including the 6m band. For DX work you need low angle radiation which is just what you get from this popular model. It will outperform dipoles when it comes to long distance contacts and even compares favourably with beams located 10m or more above ground. Unlike other verticals you don’t need long wire radials. With this antenna you get adjustable rigid radials that are self supporting, and a DC return in the base matching unit helps the antenna get rid of static noise which other models suffer from. You can adjust the antennas for each band, something you will have to do on 80m as the bandwidth is quite narrow. The radials may be arranged in a 360 degree circle or 180 degree arc.

GP-2W ZX Antennas 2-band HF Vertical 12, 17m 2-band vertical covering 12m,& 17m. 3.4 m long, it will handle 1kW and weighs 1.7kg. Input is UHF connector designed for 50 Ohm feed. Can be mounted at ground level with earth stake. Additional radial wires recommended and included. Alternatively mount in the air with supplied radial wires.

GP-3 ZX Antennas 3-band HF Vertical 10, 15, 20m 3-band vertical covering 10m, 15m & 20m. Covers the traditional 3 HF bands and is 4m long. Will handle 1kW and weighs 1.5kg. Input is UHF connector designed for 50 Ohm feed. Can be mounted at ground level with earth stake. Additional radial wires recommended and included. Alternatively mount in the air with supplied radial wires.

GP-3W ZX Antennas 3-band HF Vertical 12, 17, 30m 3-band vertical covering 12m, 17m & 30m. 5.2m long, it will handle 1kW and weighs 2.0kg. Input is UHF connector designed for 50 Ohm feed. Can be mounted at ground level with earth stake. Additional radial wires recommended and included. Alternatively mount in the air with supplied radial wires.

HF-2V Butternut 2-Band HF Vertical Antenna * Bands: 80, 40m * Power rating: 1.0kW pep * VSWR: <1.5.1 (all bands) * Bandwidth (2:1) 40m (entire band), 80m (90kHz) * Feed point impedance: 50 Ohms * Mast size: 32mm o.d. * Wind survival: 96kph (unguyed) * Height: 9.85m (32ft) * Weight: 5.9kg

Operate on 80 and 40m using the famous Butternut HF-2V vertical antenna. All 9.85m (32ft) of the HF-2V are active on both bands, maximising efficiency. Rated at the legal power on both bands. The feed point impedance is a nominal 50 Ohms. There is a handy pig-tail connection at the base of the antenna. The antenna can be mounted unguyed and comes complete with a 61cm mounting tube, 32mm (1-¼in) for direct mounting into the ground. It can be mounted using a standard TV antenna mast. The resonator coils are easily adjustable for minimum SWR. Radials not provided. This antenna is great for LF DX work. The low angle radiation will give impressive performance on DX paths. But do make sure you provide a decent earth.

HF-6V-X Butternut 6-band HF Vertical Antenna * Bands: 80, 40, 30, 20, 15, 10m * Power rating: 2.0kW pep, 500W pep (30m) * Bandwidth (2:1) 10m (entire band), 15m (entire band), 20m (entire band), 30m (entire band), 40m (280kHz), 80m (40-100kHz), * VSWR: <1.5.1 (all bands) * Feed point impedance: 50 Ohms * Mast size: 28.6mm * Wind survival: 129kph (unguyed) * Height: 7.9m (26ft) * Weight: 5.4kg The Butternut HF-6V vertical antenna operates on six bands: 80 to 10m. This efficient antenna has a vertical radiator of only 7.9m (26ft). The HF-6V is rated at 2.0kW on 80, 40, 20, 15 & 10m and 500W on 30m.The feed point impedance is a nominal 50 Ohms, matching line and RF connectors included. Superb low angle radiation. The antenna can be mounted unguyed and comes complete with a 61cm mounting tube, 28.6mm (1-1/8in) for direct mounting into the ground or it can be mounted on a standard TV antenna mast. Requires radials or capacitive counterpoise system (CPK), not provided.

HF-9V-X Butternut 9-Band HF Vertical Antenna * Bands: 80, 40, 30, 20, 17, 15, 12, 10, 6m * Power rating: 2.0kW pep * Bandwidth (2:1) 6m (1MHz), 10m (1500kHz), 12m (200kHz), 15m (entire band), 17m (200kHz), 20m (entire band), 30m (entire band), 40m (280kHz), 80m (40-100kHz) * VSWR: <1.5.1 (all bands) * Feed point impedance: 50 Ohms * Mast size: 28.6mm * Wind survival: 129kph (unguyed) * Height: 7.9m (26ft) * Weight: 6.3kg The Butternut HF-9V-X vertical antenna operates on nine bands 80m through 6m with single, highly efficient vertical radiator of only 7.9m (26ft). The HF-9V-X is rated to full legal limit on all bands. The feed point impedance is a nominal 50 Ohms, matching line and RF connectors included. The antenna can be mounted unguyed.

Radials or capacitive counterpoise system (CPK), not provided.

CPK Butternut Counterpoise Kit Substitutes for ground or elevated radials. Acts as missing half of dipole and allows Butternut models HF-6V and HF-9V-X to operate with better efficiency. Easily bolted onto base of antenna, it forms a square measuring 2.5m on each side. Not recommended for heights over 6.1m above earth

A-17-12 Butternut 17 & 12m Adaptor for HF6V-X 17 & 12m Adaptor for HF6V-X

RMK-II Butternut Roof Mount Kit Roof mount kit including tripod/STR-II radial kit/hardware for HF6/9V-X & HF2V

STR-II Butternut Resonant Radial Kit Resonant Radial Kit for above ground mounting

TBR-160-S Butternut 160m Resonator 160m resonator for HF6/9V-X & HF2V

DX-88 Hy-Gain 10-80m Vertical * Bands: 80, 40, 30, 20, 17, 15, 12, 10m * Power: 30m 250W (av), 17m 500W (av), Other bands 1500W PEP * Gain: 3dBi nominal * VSWR: < 1.5:1 typical *Vertical angle: 16 degs * Horizontal angle: 360 degs * Connector : SO-239 * Mast size: 38.1-41.275mm * Wind survival: 120 kph * Height: 7.54m * Weight: 8kg NOTE: The DX-88 is designed to be ground mounted or elevated with radials. The DX-88 offers coverage of all the HF bands of 80 through to 10m. The key design features are the adjustable capacitors that eliminate many of the tuning problems found with other verticals. The DX-88 handles the maximum legal power on all bands, features low-loss traps and has a low angle of radiation for good DX performance. Self supporting, the DX-88 comes with stainless steel hardware for long term reliability.

MFJ-1621 Portable Antenna * Bands: 40, 30, 20, 17, 15, 12, 10m * Power rating: 200W * 1.37m telescopic whip * Built-in ATU with meter * 15.24m coax feeder * Size: 153 x 76 x 153mm The MFJ-1621 is a "go anywhere" antenna. It comprises of 1.37m telescopic whip, built-in ATU, field strength meter and 15.24m coax feeder. It covers 40-10m and handles 200W. Connect feeder to transceiver adjust tuner and you are on the air! Ideal for portable operation.

MFJ-1792 80/40m Vertical Antenna * Bands: 80, 40m * Power rating: 1.5kW PEP SSB * VSWR: 1.2:1 (typical) * Bandwidth (2:1): Full band * 1/4 wave: 40m radiator * Radiation Angle: Low * Freq. Selection: Automatic * High-Q coil & capacitance hat * Requires radials or ground * Includes heavy duty mount * Requires guying * Height: 10m The MFJ-1792 high performance vertical antenna for 80 and 40m. End loading the most efficient form of loading is used for 80m. It uses a 1.37m top capacitance hat and a high-Q coil and features a full size quarter wave radiator for 40m.

MFJ-1793 80/40/20m Vertical Antenna * Bands: 80, 40, 20m * Power rating: 1.5kW PEP SSB * VSWR: 1.2:1 (typical) * Bandwidth (2:1): Full band * 1/4 wave: 40m * 1/2 wave: 20m * Radiation Angle: Low * Freq. Selection: Automatic * High-Q coil & capacitance hat * Requires radials or ground * Includes heavy duty mount * Requires guying * Height: 10m The MFJ-1793 high performance vertical antenna for 80, 40 & 20m. End loading, the most efficient form of loading is used for 80m. It uses a 1.37m top capacitance hat and a high-Q coil which is the same as the MFJ-1792 but also features a full size quarter wave radiator for 20m.

MFJ-1796 6-band Vertical Antenna * Bands: 40, 20, 15, 10, 6, 2m * Power rating:1kW 40, 20,15, 10m * 700W 6m * 300W 2m * VSWR: 1.2:1 (typical) * Bandwidth (2:1): Full band * 1/2 wave: 2 & 6m * Radiation Angle: Low * Freq. Selection: Automatic * High-Q coils no traps * No Radials or Ground * Height: 3.65m 0.609m footprint * Weight: 5.25kg The MFJ-1796 vertical antenna that will fit into a small space. Vertical antennas are known for their low angle radiation for DX working, even when erected at a low height. There are no radials and subject to safety restrictions, it can be erected as low as 1.5m above the ground. Ceramic coils and end loading ensure that losses are kept to a minimum and each band can be individually resonated.

MFJ-1798 10-band Vertical Antenna * Bands: 80, 40, 30, 20, 17, 15, 12, 10, 6, 2m * Power rating: 1.5kW PEP * VSWR: 1.2:1 (typical) * Bandwidth (2:1): Full band * 1/4 wave: 20,17,15,12,10, 2m * 3/4 wave: 6m * Radiation Angle: Low * Freq. Selection: Automatic * High-Q coils no traps * No Radials or Ground * Height: 6.7m The MFJ-1798 could be the answer to many hams problems, a vertical antenna that does not take up much space, requires no radials and covers ten bands from 80m to 2m. With a total height of 6.7m, this antenna exhibits very low angle radiation and so is ideal for DX operation. All you need is a single coaxial feed line to give you ten band operation with automatic switching.

PBX-100 Watson Portable HF Antenna * Bands: 80, 40, 20, 15, 10m (Including WARC Bands) * Power rating: 200W PEP SSB * VSWR: 1.2:1 (typical) * Bandwidth: Depends on band * Loaded coil resonators * Radiation Angle: Low * Freq. Selection: Automatic * Ground plane wire provided * Includes ground spike + clamps * No guying necessary * Height: 2m (approx) The PBX has been designed as a portable HF vertical, ideal for carrying around in the car and using by the side of the road or in a field. Able to handle 200W, it can be used with all the popular compact HF transceivers. Packed down it measures around one metre in length. Erected it extends to around 3.6 metres. A ground spike and all necessary radial wire is included. The antenna is completely self-supporting.

MA5V Cushcraft 5-band HF Vertical * Bands: 10, 12, 15, 17, 20m * Gain: 1-2dBi * Power rating:250W PEP * VSWR: 1.2:1 (All bands) * Bandwidth (2:1) kHz 10m (500), 12m (100), 15m (450), 17m (100), 20m (200), * Vert. Rad. Angle: 16 degs * Height: 4.48m * Mast size range: 31.8-51mm * Wind survival: 160 kph * Weight: 2.95kg The MA5V is Cushcraft’s newest multiband HF vertical antenna. It provides 5-band coverage on 20m through to 10m. Power rating is an excellent 250W (PEP). VSWR at resonance is 1.2 with usable bandwidths of 200, 100, 450, 100 and 500kHz. The antenna does not require radials and is the perfect choice for patios, backyards and small gardens. It can be quickly dismantled and stored if necessary.

R-8 Cushcraft 8-Band Vertical Covering from 40m to 6m (including WARC bands) this is an ideal vertical for those with limited space that want a good low angle radiator for DX operation. Max power rating 2kW. Short base radials are included (approx 1.24m long). Feed is 50 Ohm coax via SO-239. Antenna covers full bandwidth of all bands (2:1 VSWR) except 10m where the bandwidth is 1.5MHz.

R8-GK Cushcraft Guy Kit for R8 Guy Kit for R8 Vertical

R-6000 Cushcraft 6-Band Vertical * Bands: 6, 10, 12, 15, 17, 20m * Gain: 3dBi * Power rating: 1.5kW * VSWR: 1.2:1 (typical) * Bandwidth (2:1) kHz 6m (3000) 10m (1700) 12m (100) 15m (450) 17m (100) 20m (300) Radiation angle: 16 deg * Horiz. Rad. Pattern: 360 deg * Height: 5.8m * Mast size range: 38-44mm * Wind loading (m2): 0.14m * Weight: 5.6kg The R6000 is a 6m through to 20m, no ground radial antenna. It includes many of the features of the R7000, R7 and R5 antennas. There are no traps used on 6, 10 and 15m for maximum efficiency and power handling. It’s easy to install, has automatic band changing 6 to 20m and a slim profile. Take full advantage of the new HF/50MHz transceivers and operate on 6m.