IC-775DSP
This information is taken directly off of the ICOM IC-775DSP
brochure.
IC-775DSP SPECIFICATIONS
GENERAL
- Frequency Coverage:
- Receive
- 100khz-29.990 MHz
- Transmit
- 1,800-1.999999 MHz*1
- 3,500-3.999999 MHz*2
- 7,000-7,3000 MHz*3
- 10,100-10,150 MHz
- 14,000-14,350 MHz
- 18,068-18,168 MHz
- 21,000-21,450 MHz
- 24,890-24-990 MHz
- 28,000-29,700 MHz
-
- *11,830-1,850 for Spain version; 1,810-1,850 for
France version;
1,815-1,835/1,850-1,890 for Germany version
- *23,500-3,800 for Spain, France and Germany versions
- *37,000-7,100 for Spain, France and Germany versions
- Mode: SSB, CW, AM, FM, RTTY
- Number of memory channels: 101(99 regular, 2 scan edges)
- Antenna impedance : 50 ohms nominal
- Usable temperature range : -10�C to 60�C (14�F to140�F)
- Frequency stability: Less than �200 Hz from 1 min. to 60 min. after power ON. After
that rate of stability less than �30 Hz/hr. at + 25�C (+77�F).
Temperature fluctuations O�C to +50�C (+32�F to + 122�F)
less than �350 Hz
- Power supply requirement: 120 V Type 85-135 V AC 230 V Type 187-265 V AC (switchable)
- Power consumption:
- Transmit
- max. power 760 VA
- Receive
- squelched 140 VA
- max. audio 150 VA
- Dimensions:
- 424(W) X 150(H) X 390(D) mm
- 16 11/16(W) X 5 29/32(H) X 15 11/32(D) in
- Weight: IC-775DSP 16.7 kg (36.8 lb), IC-775 16.5 kg (36.4 lb)
Transmitter
- Output power: SSB/SW/RTTY/FM 5-200 W
AM 5-50 W
(continuously adjustable)
- Spurious emissions : Less than -60 dB
- Carrier suppression : More than 40 dB
- Unwanted sideband suppression : More than 55 dB
- Microphone impedance : 600 ohms
Receiver
- Receive system
- ;SSB, CW, RTTY, AM: Quadruple conversion superheterodyne
- FM: Triple conversion superheterodyne
- Intermediate frequencies
MODE |
SSB |
CW,RTTY |
AM |
FM |
1st |
69.0115 MHz |
69.0106 MHz |
69.0100 MHz |
69.0100 MHz |
2nd |
9.0115 MHz |
9.0106 MHz |
9.0100 MHz |
9.0100 MHz |
3rd |
455 kHz |
455 kHz |
455 kHz |
455 kHz |
4th |
10.695 MHz |
10.695 MHz |
10.695 MHz |
- |
- Sensitivity (Preamp 1 On)
SSB, CW, RTTY |
100 - 500 kHz |
Less than 2.0 �V |
(10 dB S/N) |
1.8 - 29.9 MHz |
Less than 0.16 �V |
AM (10 dB S/N) |
0.5 - 1.8 MHz |
Less than 13.0 �V |
|
1.8-29.99 MHz |
Less than 2.0 �V |
FM (12 dB SINAD) |
28-29.99 MHz |
Less than 0.5 �V |
- Squelch Sensitivity (Preamp 1 ON)
SSB, CW, RTTY, AM |
Less than 3 2 �V at threshold |
FM |
Less than 0 32 �V at threshold |
- Selectivity (normal filter selection)
SSB |
More than 2 4 kHz/- 6 dB |
|
Less than 4 0 kHz/ -60 dB |
CW, RTTY |
More than 500 Hz/-6 dB |
|
Less than 1 0 kHz/-60 dB |
AM |
More than 2 4 kHz/-6 dB |
|
Less than 4 0 kHz/-60 dB |
FM |
More than 15.0 kHz/-6 dB |
|
Less than 30.0 kHz/-60 dB |
- Spurious and image rejection ratio: More than 70 dB
- Audio output power: More than 2 6 W at 10% distortion with an 8-ohm load
- RIT/
TX (variable range) �9.999 kHz
ANTENNA TUNER
- Matching impedance range : 16.7 - 150 ohms unbalanced (Less than VSWR 3 : 1)
- Minimum operating input power: 8 W
- Tuning accuracy : VSWR 1.5 : 1 or less
- Insertion loss : Less than 1.0 dB (after tuning)
All stated specifications are subject to change without notice or obligation.
OPTIONS
- IC-4KL HF 1 kW LINEAR AMPLIFIER This is an all solid-state, full-duty 1
kW linear amplifier including an automatic antenna tuner. The IC-4KL is fully controllable
from the IC-775/DSP. No need to tune and no need to switch the operating band. Full
break-in (QSK) operation is possible. The amplifier/power supply unit and the remote
control unit are separated.
- IC-2KL HF 500 W LINEAR AMPLIFIER This is an all solid-state 500 W
linear amplifier. The power amplifier unit can be separately set-up from the power supply
unit.
- IC-AT500 500 W automatic antenna tuner. Best match for the IC-775/DSP
with the IC-2KL. Includes an automatic antenna selector for 4 separate antennas.
- EX-627 AUTOMATIC ANTENNA SELECTOR Automatically selects the antenna for
the selected ham band. Manual selection is also possible. Max. input power: 1000 W PEP
- MB-19 Mounting handles for 19-inch rack.
- SP-20 4 Audio filters; headphone jack; can connect to 2 transceivers;
style/size matched to the IC-775/DSP. Input impedance: 8ohms. Max. input power: 5 W.
- SP-21 Designed for base station operation. Input impedance: 8ohms. Max.
input power: 5 W.
- SM-20 Unidirectional, electret microphone for base station operation.
Includes (UP)/(DOWN) switches and a low cut function.
- SM-8 Electret condenser-type desktop microphone including 2 connection
cables for simultaneous connection of 2 transceivers. (UP)/(DOWN) switches are included.
- CT-16 Easy tuning when connecting another Icom HF or V/Uhf transceiver
for instant satellite communications.
- CT-17 For remote transceiver control using a personal computer equipped
with an RS-232C port. You can change frequencies, operating mode, memory channels, etc.
- HM-36 Hand microphone equipped with (UP)/(DOWN) switches.
- CR-282 Contains a temperature-compensating oven heater and crystal unit
for improved frequency stability. Frequency stability: � 0.5 ppm
- UT-66 Announces operating frequency and mode.
- UI-100 Enables several digital functions, such as noise reduction, for
the IC-775 (non-DSP type). Already installed in the IC-775DSP.
- FL-101, FL-102, FL-223 9 MHz FILTERS Have good shape factor and provide
you with better reception.
- FL-101: 250 Hz/-6dB (CW nar.)
- FL-102: 6.0 kHZ/-6dB (SSB wide/AM med./FM nar.)
- FL-223: 1.9 kHz/-6 dB (SSB nar.)
- FL-53A and FL-222455 kHz FILTERS Have good shape factor and provide you
with better reception.
- FL-53A: 250 Hz/-6 dB (CW nar.)
- FL-222: 1.9 kHz/-6 dB (SSB nar.)
Back to IC-775DSP Summary
[ICOM Homepage] [Dealers]
[New Radios] [Calendar] [Specials] [Get in Touch With ICOM]
Copyright 1995 ICOM AMERICA, INC. All specifications and options subject to change without
notice or obligation. NOTE: All specifications are for U.S.A. versions. For specifications
in other countries, check with your ICOM Dealer. Some options may not be available due to
local regulations.