Subject: FT51 MOD
Newsgroups: rec.radio.amateur.misc

In article <3hbg59$39t@news.csus.edu> you write:
Marc B. Grant (marcbg@metronet.com) wrote:

:  A  few  months  ago  I  posted the mod to allow expanded receive on the :
FT-51R.  Has  ANYONE  checked  out to see if there are more mods? Is there :
more expanded receive other than 130-170 and 410-470?

	I posted this a while back, but here it is again...

YAESU FT-51R

Expanded Transmit 140-174 MHz, 420-470 MHz

MARS & CAP MODIFICATION

 This information is authorized for distribution only to individuals who are
members  of  the  U.S. Military Affiliate Radio System, Civil Air Patrol, or
other  government  agency  services specifically permitted by the FCC to use
non-Type-Accepted  equipment  such  as  that  utilized  in the Amateur Radio
Service. Release of this information to individuals not bearing a license in
the  MARS,  CAP, or other such government service is not authorized by Yaesu
U.S.A.

	*	Remove Antenna and Battery

	*	Remove (6) black screws in rear plastic cover plate
		(where the battery would normally fit)

	*	Remove the (1) small black screw in the battery slide switch
		(see figure 1 below for screw locations)

	*	Loosen (but don't remove) the (4) black screws on the upper
		back of rear case and slightly separate the rear radio
		case.

	*	Remove the "L" type plastic cover

		CAUTION: Watch out for the delicate ribbon cable

	*	Locate and unsolder jumper pad #6 (see Figure 2 below
		for jumper locations) (Pads 1,7 should now be jumpered)
		(Stock, Pads 1,6,7 only)

	*	Reinstall the "L" type plastic cover

	*	Tighten the (4) case screws on rear case

	*	Re-install the (6) black screws in rear plastic cover
		plate.

	*	Re-install the (1) small black screw with the battery 
		slide switch

	*	Now attach the antenna and battery

	*	Turn off Radio...  Press and hold both UP & Down Arrows
		Keys (right side) while turning on the Radio

	*	Modification now complete!


	(Figure 1 not rendered; my ASCII art skills aren't that good)


	Figure 2:  Jumper locations.  For European tone burst, add solder 
to jumper 4.


	_________________________________________________
	|
	|      __________
	|      |        |    1 o
	|      |        |          o 2
	|      |        |    3 o
	|      |  CPU   |          o 4
	|      |        |    5 o
	|      |        |          o 6
	|      |________|    7 o
	|
	|
	|




 --
 Dan Brown, KE6MKS
 danb@acme.csusb.edu -- finger for PGP 2.6.1 public key
 Don't Tread on Me




From: taucom@kaiwan.com
Organization: Stat Gateway Service, WB7TPY
>Subject: Yaesu
X-Article: 722
Content-Type: text
Content-Length: 1896
X-Lines: 60


Kevin K. of Yaesu provided some great info about their new FT-51R HT, at the
recent  meeting. He also described some undocumented features. For those who
want a hardcopy of this, here it is.

YAESU FT-51R Soft-Modifications - undocumented:  February 1995

The  new  FT-51R  utilizes  software  to  control  the  various deeper level
functions instead of some traditional pots.

To access this undocumented menu:

1.  Turn on radio, and select band you want to modify.
2.  Turn off the radio.
3.  Simultaneously press the 2 VOLUME keys and the CALL buttons while
    powering on.
4.  You're now in the soft-mods menu.
5.  You'll now see the following menu choices while turning the DIAL
    knob:

    BAND 1 (top of menu)
    IF NO 0
    S-FULL84
    S-1 19
    SQL TH64
    SQL TI4E
    MOD L 25
    MOD H 27

The  only  soft-mod  I'm  familiar  with  so far, is to change the deviation
setting for the mike.

Turn the dial until you see MOD L 25:
    1.  Press the FUNCTION key down for 1/2 sec. until F flashes.
    2.  Press the /\MHz or \/MHz to change the numerical value.
    3.  Press the FUNCTION key again to save this change.
    4.  Do the same for MOD H 27.
    5.  Power off.

I'm  not sure exactly what the numerical values mean, so experimenting is in
order.

I'm also unclear as to what the other menu items are. I believe they have to
do with squelch settings, i.e., threshold.

I've  also  been  told  that  the  software can be controlled by an external
computer,  by  accessing  the handshake via simultaneously pressing 2 and 9,
and powering on (remember MH-29, model # of the LCD mike). I don't know what
connector or software is needed.

Please send any info you have on these soft-mods.


 




     *================================================================*
     *    << BBS "ARACHAN" CX3VB >> - << CX3VB-6 APRS Digipeater >>   *
     *----------------------------------------------------------------*
     *   HF 7.040 Khz  VHF 145.010 Khz  AX25 CX3VB@CX3VB.CELA.URY.SA  *
     *   E-Mail cx3vb@qsl.net  -  cx3vb@amsat.org (Solo Texto plano)  *
     *----------------------------------------------------------------*
     *  Jose Maria Techera - Melo, Cerro Largo, URUGUAY, SA (GF27WO)  *
     *================================================================*

