Subject: FT-50

You  take  off the battery pack.. remove the sticker on the radio.. undo the
screws (but not all of the way)-- you push on the screws and the keypad will
come  loose  on the other side. Undo the screws all of the way to get access
to  underneath the keypad. There are 3 areas where there can be colser pads.
Remove the #1 solder pad . AKA there should bo NO solder pads connected. Put
the  radio  back together.. and reset the cpu and enable the Extended RX mod
by using the "knob". It will now go just about everywhere.

Subject: Yaesu FT-50R Guide V 1.1
From: childers@garlic.com (Bill Childers)


The (In)Complete Guide to the Yaesu FT-50 Version 1.1

Compiled by Bill Childers, KE6VVW

Disclaimer  &  Other Nonsense The information in this document is a guide to
the  FT-50 ONLY. Having had more than a few radios in my amateur experience,
I  understand  how  most  hams  wish  to  learn  as much about their rigs as
possible.  I  have  compiled  this guide to allow other people to learn more
about  the radio without having to search all over for information. I do not
guarantee  the validity of this information, as Yaesu may change programming
or  hardware  so  that  some of the techniques in this document may cease to
function. I am not responsible if these instructions damage your rig in some
way.  All  I can say is that I have performed the following procedures to my
unit, and I am quite pleased with the results. Your mileage may vary, etc.

 
History

Version 1.0
1st introduced.

Version  1.1  Added:  Game  mode, Changed High Power Mod to "Internal System
Alignment".   In  this  section  I  also  detail  the  squelch  and  S-meter
adjustments. Also added info to the bug on the FTT-12 Keypad.



Introduction

The  Yaesu  FT-50  is  perhaps the most unique VHF/UHF Handheld manufactured
today.  Its made to MIL-SPEC 810, for dust, splashproofness, and vibration.
Out  of  the  box,  it has not only dual band 2m/440 capability, but wide FM
receive and AM receive as well. In addition, it receives 76-200 MHz, 380-500
MHz,  and  700-900  MHz  (Cellular  Blocked). It has one of the fastest scan
speeds  for  an  amateur  HT.  It  also  has  the unique ability (w/ ADMS-1C
software)  to interface with an IBM PC running Windows and have memories and
settings  uploaded/downloaded.  In  addition,  it  has  DCS  (digital  coded
squelch),  ARTS  (auto-ranging  transpond  system),  and  Yaesus  excellent
transmit  and receive battery saver features. It also uses Yaesus extremely
efficent  FET  power  module that allows for 5W+ of output power with a 9.6V
battery  pack. With the optional FTT-12 keypad, the unit also performs CTCSS
decode,  DTMF paging, and also incorporates a Digital Voice Recorder! All of
this functionality in such a small package makes it my rig of choice.

Problems (Bugs)

Unfortunately,  the  FT-50  is  plagued by a few bugs. None of them are very
serious  or  life-threatening,  just a bit annoying. First among them is its
Wide-FM  receive. Apparently Yaesu engineers didnt put a wide enough filter
in the unit, and some of the bandwidth of broadcast FM signals gets "chopped
off".  This means that the rig is near useless for listening to music on the
broadcast  FM band. It works marginally with voice only on the same band. My
opinion  on  this  problem:  If  you  want to listen to music, bring a small
Walkman  or other transistor radio with you. The 50 does an adequate job of
bringing  voice  signals  in  on broadcast FM, so its good for listening to
emergency  broadcasts.  The second "bug" lies in the optional FTT-12 keypad.
The  manual  for the radio states that you can set up a "voice mail" type of
functionality  that  lets your radio operate unattended and record calls for
you.  This mode doesnt work correctly, although the built-in voice recorder
works great. It seems that the unit will playback the wrong voice partition.
The  problem  appears  to  be  in  the DTMF page-answer-back area. If youre
buying  the  50  and FTT-12 solely for this purpose, DONT! It doesnt work
and theres no current workaround. The third bug has been complained about a
bit. It seems that some 50s suffer from a low Tx audio problem. This is due
to  a  factory  adjustment  that  is set a bit on the low side. It is easily
fixed. (See Factory Adjustments below). The fourth "bug" is synergistic with
the ADMS-1C software. If there is some kind of problem in downloading a file
to  the  radio,  the software aborts with an error, and the rig is left with
its  memories  cleared  in  a  "limbo"  state.  This  state is actually the
European band plan, and if done properly, the rig can be modified to receive
even  more  frequencies  which  will  be described later. (See modification
section) However, if you want to return the rig to its natural state, simply
download  a  blank  frequency  file  (NONAME.RDF) to the unit. All should be
well.

Factory adjustments

If your rig suffers from the low Tx audio problem, heres how to fix it.

1. Remove the battery and antenna.

2. Remove  the  "NiCd"  sticker  on  the  heat  sink. If you remove it very
carefully, its possible to re-install it later with the same stickum thats
on it.

3. Look in the cavity where you removed the sticker. Proceeding from left to
right,  heres  what  youll  see Phillips head Screw (Holds the keypad in)
Small  Silver  Potentiometer  (VR1001VHF Deviation Adjustment) Small Silver
Potentiometer  (VR1002UHF  Deviation  Adjustment) Small White Potentiometer
(TC1001DONT TOUCH! CTCSS Tone Adjustment!!!) Phillips head Screw (Holds the
keypad in)

4.  Take  a  small Phillips head Screwdriver and turn both VR1001 and VR1002
about  1/8  turn clockwise. This will increase the VHF and UHF deviation and
fix  the low Tx audio problem. If its not enough Tx audio, simply turn both
pots another 1/8 turn. Make sure to turn both pots the same amount!

5. Replace the NiCd sticker, battery, and antenna.
6. Youre Done!

Internal  System  Alignment (May not work on some radios) NOTE: This setting
appears  to  work on radios that have NO MEMORIES programmed. You might want
to  try  STEP  3  before clearing your memories. If step 3 doesnt work, you
probably  need  to clear your memories. BE CAREFUL with these settings its
possible  to  really  mess  the  rig  up  by  setting  some funky squelch or
something you might want to write the default settings for your rig down.

1. Select 2m VFO frequency.
2. Turn the radio off.
3. Push LAMP, PTT, Knob, and PWR at the same time. The rig will turn on with
the squelch open, so turn the volume down!
4. The  50  will  display "BAND xxxxxx" where xxxx may differ depending on
your radio and whatever mods you may have performed.
5. Turn the top knob. There are a variety of settings available.
Here  is  a listing of them:  HSSQ: Squelch Hysteresis Adjustment, adjusted
by the dial.  THSQ: Squelch Preset Threshold  TISQ: Squelch Preset Tight 
S1LV:  Low-Scale  S-1  Adjustment.   S9LV: S-Meter Full Scale Adjustment. 
HIPO:  Hi  Transmit  Power  Adjustment:  Should be calibrated for 5W (Can be
pushed  higher with a 13.8V Supply)  L3PO: Level 3 Power Adjustment: Should
be  adjusted  for 2.8W.  L2PO: Level 2 Power Adjustment: Should be adjusted
for 1W.  L1PO: Level 1 Power Adjustment: Should be adjusted for .1W.
6. Select the adjustment you wish.
7. Push  in  the  Top  knob.  There  will be a "s" that appears next to the
displayed number.
8. Rotate the knob to change the setting.
9. Change other settings, if desired.  
10. Push the knob for more than 1 sec to save the profile.
11. Select 440 VFO frequency.
12.  Repeat  Steps 3-10 to adjust the UHF Settings. UHF Settings will have a
"U" in front of them.


Modifications

The  FT-50  is extremely easy to modify. The first modification is performed
for  you at the factory but for those of you who accidently disabled it, or
changed it here it is.

Extended U.S. Receive Mod (Expands receive from 144-148 & 430-450 to 76-200,
380-500, 800-999 cell blocked) NOTE: All memories will be erased.

1. Turn the transceiver off.
2. Hold down the Knob and Lamp keys while powering the unit on.
3. The unit now has U.S. Extended Receive.

  MARS/CAP  mod  (Extended  Transmit  Mod:  app. 144-159, 420-470) NOTE: All
memories  will  be  erased. Dont transmit on bands that youre not licensed
for!!  Besides  being  illegal,  it  creates problems for people using those
frequencies.

1. Remove battery & antenna
2. Remove NiCd Sticker on Rear Heat Sink
3. Loosen (Dont Remove) Philips head screws on rear that hold 
keypad in.
4. Use screws as thumb holds to press keypad out.
5. Remove screws.
6. Remove Keypad.
7.  Under  Keypad on Left Side there is a series of Solder Jumpers. They are
labeled in white from 1-3. Only #1 will have solder jumpering it. Remove the
solder,  being careful not to damage or touch any other components. WARNING:
If  youre  not  good at desoldering, or have shaky hands, you might want to
have someone else do this for you. Its REAL easy to damage the rig.
8.  Reinstall  Keypad. Be careful of the O-ring around the keypad. Make sure
its  not  twisted  or  damaged,  as the waterproofness of the unit could be
compromised.
9. Install sticker, battery and antenna.
10.  Hold  down  Knob  and  Lamp  keys while powering the unit on. (Extended
Receive Mod as above.)
11. Completed!

Super-Hyper  Awesome  Mod  The  mother  of  all  Mods!!!  (Requires ADMS-1C
software  and  MARS/CAP  mod  to  be  performed)  Receive:  76-999  Mhz  (No
displayable  holes!!!)  Transmit:  120-221  Mhz,  320-499  Mhz (AGAIN, Dont
transmit on frequencies where youre not licensed)

NOTE:  This  mod will disable ARS (automatic repeater shift) and will set 2m
and  440  repeater  offset  to  weird  numbers. Make sure you enter repeater
offset and +- shift manually.

Repeater  offset needs be set once for the rig, then it should be able to be
forgotten  about.  It  will  also  clear  memories.  Remember  above where I
mentioned  the  ADMS-1C software having a bug? Heres where the enterprising
and  curious  ham  can  take  advantage  of  that. This mod will install the
European  band  plan in your radioso without the MARS/CAP mod you will lose
the top portion of your 2m band.

1.  Are there frequencies in your radio? Dont want to lose them? Simply get
the  data from your radio as it sits you can "merge" the frequencies later.
Save the file.

2. Perform the MARS/CAP mod as outlined above. Get the data from the mod and
name it USA.RDF.

3. Attempt to send the same data to the radio. In the middle of the transfer
(around 50%), pull the adapter cable to the PC out of the radio.

4.  Thanks  to  the  bug,  your  radio  is now in European mode! Perform the
Extended  Receive  Mod  by holding the Knob and Lamp keys down while turning
the unit on.

5.  Now,  the Automatic Repeater offset doesnt work. Theres no workaround.
Note  that the 2m offset has been changed to 0.00. Go to the menu by holding
down  the  knob. Go to SHFT, Option 7. Press the knob. Turn the knob so that
it reads 0.60. Press PTT.

6.  Now, turn off the radio. Put it back into clone mode. Read the data back
from the radio to the PC and save the file as EURO.RDF.

7.  If  you  want  to enter frequencies manually or using ADMS as normal, go
ahead.  Everything  should  work.  If  you  saved frequencies as above, open
EURO.RDF  and  "merge"  the  frequencies from your USA.RDF file into it, and
save  it  as  another  name. Then send the modified EURO.RDF (your filename)
file back to the radio using the "template" file EURO.RDF. Youre done!

8.  To  return  the  radio back to the U.S. band plan, send the USA.RDF file
back  to  it.  Note  that  I have no way of measuring the sensitivity of the
frequencies or the output power of the rig outside of the ham bands. The 220
coverage  seems  to  be  very  poor,  however,  the  radio  does display 220
frequencies.  It wont transmit on our 220 bands, though. 800 Mhz receive is
vastly improved.

Game  Mode  The FT-50R includes an interesting "game" thats programmed into
it. Heres how it works:

1. Power up the radio while holding down the MR key. (PWR + MR).

2.  The  display  will  show  GAME on the left side, and Spd 1 on the right.
Youre in game mode!

3.  By  rotating  the  knob,  you  can  change the speed of the game. Higher
numbers are faster.

4. Press PTT to start the game.

5.  Numbers  will  start  to scroll across the screen from left-to-right. As
they  come,  you  are supposed to push the number on the keypad that makes a
sum  of  ten,  followed  by F. Example: 6 appears, press 4, F. If 0 appears,
enter 10 followed by F.

6. The game is over when the screen fills up with numbers.

7. To exit the game, simply cycle the power.







     *================================================================*
     *    << BBS "ARACHAN" CX3VB >> - << CX3VB-6 APRS Digipeater >>   *
     *----------------------------------------------------------------*
     *   HF 7.040 Khz  VHF 145.010 Khz  AX25 CX3VB@CX3VB.CELA.URY.SA  *
     *   E-Mail cx3vb@qsl.net  -  cx3vb@amsat.org (Solo Texto plano)  *
     *----------------------------------------------------------------*
     *  Jose Maria Techera - Melo, Cerro Largo, URUGUAY, SA (GF27WO)  *
     *================================================================*

