FT-470 mod extended VHF xmit....

Here's the mod for the FT-470. (I have not performed it myself)
1. Remove Cover
2. Remove Lithium battery carefully
3. On left hand side locate some empty vertical pads, one above the other.
It should be marked as R-69. There is also a chip resistor R-67 that
is just below it to the left a bid.
4. Place a solder jumper across the two R-69 pads.
5. Reinstall the lithium battery.
6. Closeup the Radio.
7. Turn the radio of. While pressing down the up and down arrow keys,
turn the radio back on.

Note: This mod only opens up the VHF transmit frequency range
beyond 140 to 150. The automatic repeater offset will
be defeated so you will have to enter the +/- offset yourself.

73's     Bernie NU1S @ K1UGM

Note: I haven't tested this, proceed at your own risk.  Don't
transmit out of band, else you might get a fine or even do time.
WA2ISE

------------------------------

Date: 26 Aug 90 00:39:28 GMT
From: mailrus!hellgate.utah.edu!uplherc!wicat!keithm@tut.cis.ohio-state.edu
 (Keith McQueen)
Subject: FT-470 mods
To: info-hams@ucsd.edu

I have recevied enough enquiries about mods for the Yaesu FT-470
hand held, that I have decided to post what I know.


(This is a transcription of a letter that I received detailing
the CPU programming jumpers that were found experimentally
by Ed Boakes, WB3FLD.     Keith, N7HMF)

Dear Keith,

A little while ago, I came across a Net News item from you about the
Yeasu FT-470 handheld.  You asked if anyone knew how to make it
receive the public service band just above the UHF amateur band.  Well,
I've figured out how to do that.  However, the bad news is that when
you strap the unit for this mode, it only transmits from 430 to 440!
Oh, well.

I gave you a phone call a week or so ago, but it seemed that we kept
missing each other.  Anyway, here is what I've learned about the
FT-470:  I have located a total of eight straps, the four which you
had written about, to the left of the lithium battery, and four others
located under the flat white cable that interconnects the upper half
with the lower half.

                 YEASU FT-470 STRAPS
R69  Vertical, at the 10 o'clock position by the lithium cell
R68  Horizontal, to the lower left of R69
R67  Horizontal, just below R68
R66  Horizontal, just below R67

R71  Vertical, the leftmost of three, to the left of the upper
     corner of the ribbon cable connector.
R70  Vertical, the center of three of which R71 is the leftmost
R72  Vertical, the rightmost of the three
R74  Vertical, to the left of the ribbon cable connector, below
     the three.  (Note that R74 is below an unpopulated capacitor
     that does not have a C number.

There is no R73, or at least it is not on the circuit board and it is
not in the schematic.  And, yes, the order of those three is indeed
R71, R70, R72, left-to-right.

R70, R71, R72 select the mode for the UHF portion of the FT-470.  The
choices are:


                           UHF CHOICES
R71    R70    R72          Rx and TX             Receive only
0      0      0            430 to 440 Mhz        430 to 500 Mhz
0      0      1            430 to 450 Mhz
0      1      0            430 to 440 Mhz
0      1      1            432 to 438 Mhz
1      0      0            430 to 440 Mhz
1      0      1            220 to 225 Mhz
1      1      0            430 to 440 Mhz
1      1      1            210 to 235 Mhz
R66, R67, R68 and R69 select the mode for the VHF portion of the FT-470.
The choices are:

                          VHF CHOICES
R66   R67   R68   R69      Rx and Tx             Receive only
0     0     0     0        144 to  146 Mhz        130 to 180 Mhz
0     0     0     1        144 to  146 Mhz
0     0     1     0       1260 to 1300 Mhz
0     0     1     1       1240 to 1300 Mhz
0     1     0     0        140 to  150 Mhz        130 to 180 Mhz
0     1     0     1        140 to  174 Mhz
0     1     1     0        303 to  343 Mhz
0     1     1     1        8AL to  242 Mhz
1     0     0     0        144 to  148 Mhz
1     0     0     1        144 to  146 Mhz
1     0     1     0       1240 to 1300 Mhz
1     0     1     1        404 to  444 Mhz
1     1     0     0        140 to  160 Mhz
1     1     0     1       1260 to 1300 Mhz
1     1     1     0        101 to  141 Mhz
1     1     1     1        1R3 to 158L Mhz
(Note: the receive only ranges are enabled by powering up the
       unit with the up and down arrow buttons depressed...kjm)

When  there is more than one combination which has the same frequency range,
the  difference is the default step size and/or the default repeater offset.
Of  course,  choices  that  do not match the VCO and filters do not actually
transmit  or receive on those frequencies. A particularly strange example is
that  the  VHF  side  of the set can be set to tune from 404 to 444 Mhz, but
again,  it  won't  actually lock. Even in the 101-141 mode, the VHF VCO will
not  lock  - this must be for use with some other sort of VCO (It looks like
this  would cover the aeronautical band rather nicely.) There are two really
wierd  VHF  settings,  those for 8AL-242 and 1R3-158L. These must be for use
with  some  other  LCD  controller  -  it  displays  truly  unusual  and non
sequential thins when stepped through the "bands".

R74  seems  to  have  something  to  do with something like selecting the IF
frequency,  or  something else like that that. When set, it really screws up
the VHF reception.

My  technique for determining these straps is to remove the straps that come
in  the  unit,  solder wires to each pad, run the wires out of the unit to a
bank  of DIP switches, screw the unit back together, and then go through all
of  the  DIP  switch  combinations. I usually use a stereo microscope and 30
guage  wire  for  this.  Since  I didn't try powering the unit on with every
combination  of  keys  held  down for each DIP switch combination, there may
still be other secrets possible.

Since  I  was  looking  for something like receive and transmit from zero to
infinity,  and I didn't find it, I kept looking until I got bored and wanted
to  button  the thing up and start using it. I determined, from studying the
schematic,  that  there should be a hiddem strapping diode from CPU pin 2 to
CPU  pin  22. I installed one, but nothing changed. In fact, changing it and
powering the unit up did not cause a reset. Therefore, I concluded that this
really wasn't a mystery strap, afterall. However, there could be others. I'm
trying  to  get a data sheet for the CPU, from Hitachi, to see if any of the
grounded  pins  are  actually  I/O  pins  --  they might be good candidates,
particularly  if  their  traces  are  routed  in  such a way as to be easily
accessible for cutting.

I've  learned  that  one  of  the  ways  to get some of the other, new Yeasu
handhelds  to  go  out-of-band, involves dumping data out of the clone port,
editing  the  data, and then dumping it back in. I called Yeasu and asked if
the  FT-470  could  be  cloned.  They  said no, so I ignored them. I haven't
figured  out  how to get it to dump data, but I believe it will accept data.
The  clone mode is entered by powering up the unit with the F key held down.
(It's  also  a  neat  way to see all of the indicators on the LCD!) The data
must  be  presented in the ring ("right channel") of a stereo 2.5 millimeter
plug  which  is  placed into the mic jack. This is cryptically marked on the
schematic,  anyway.  However,  I  have  no idea what the format for the data
should  be.  If you come across this, I'd love to know. This may be the trap
door to getting the rig to receive and transmit in more interesting places.

Have fun with you FT-470!

Yours Truly,
Ed Boakes

CAll: WB3FLD
email: att!hocpa!ewb
work: (201) 834-1121
Fax: (201) 834-1371
home: (201) 957-0391



Several  interesting  things  that  I  have  learned  since  I received this
letter... According to the guys at Yaesu, the engineers in Japan appearantly
wrote the full UHF rx/tx out of the ROM on purpose.

The unit does a very good job as a cross-band repeater.

To  enable this, turn off the radio, hold the RPT key and turn on the radio.
Now, anything heard on EITHER band will be re-transmitted on the other band.
There are, however, a few problems.

First, there is no real internal path for the audio to get from the receiver
to  the  transmitter,  so  you either have to modify the radio, to provide a
path, or do what I did which is build a short loop back cable connecting the
tip of the earphone jack to the tip of the microphone jack like this:

     <=====----/\/\/\/\/\/\/=====---->
                   100K

This  is  the  way I did it, others I have talked to have used either just a
resistor  like  me or a small capacitor, or a combination. On my radio, this
value  of  resistor  gave  me  a  good  range  of tranmitted audio levels by
adjusting the volume control.


The other small problem is that the radio automatically selects low power on
transmit  in  this  mode.  This  is  probably  because of the lack of a real
duplexer.

After looking through the service manual, it became appearant that the small
mystery  hole  on  the side of the radio with the rubber plug was originally
intended for an external power jack. I have not yet asked Yaesu if they will
sell the jack for that spot. I also have no idea why they omitted it.

All in all, I still love my FT-470.  Its a great little radio.





     *================================================================*
     *    << BBS "ARACHAN" CX3VB >> - << CX3VB-6 APRS Digipeater >>   *
     *----------------------------------------------------------------*
     *   HF 7.040 Khz  VHF 145.010 Khz  AX25 CX3VB@CX3VB.CELA.URY.SA  *
     *   E-Mail cx3vb@qsl.net  -  cx3vb@amsat.org (Solo Texto plano)  *
     *----------------------------------------------------------------*
     *  Jose Maria Techera - Melo, Cerro Largo, URUGUAY, SA (GF27WO)  *
     *================================================================*
