Hello to all the owners of the FT-411 OF YAESU,

 I have this Hand held, and by playing with it, I discovered a nice trick to
increase  it frequency coverage. It is so simple that you don't even have to
open your hand held. All you have to do is:

 1. Make sure that the power switch is off.

 2. press the UP arrow and DOWN arrow together, at the same time (those keys
are  also  called  A,  and B. and they placed at the upper right side of the
keyped)

  3.  Keep  pressing both buttons and turn the power on. That's all. Now you
can  receive  130-174Mhz,  and  transmit 140-150Mhz CAUTON: When you do this
modification  the  memories  can be erased. Ayhow I think it is not the end,
and  there are some more options. If you do have some more information about
this Hand held, Please leave me a msg with it.





Date: Thu, 16 Feb 89 14:26:30 EST
Subject: more mods
From: rfc@briar.philips.com (Robert Casey;6282;3.57;$0201)
Subject: FT 411 mods


 copied from packet:
 Msg# TSP  Size Read To     @ BBS  From    Date  Time
 24250 BN   2876    1 YAESU         4X6TL  890208 1513
 Subject: FT-411 Modification.

           From: 4X6TL@4Z4SV

           Hi everybody.
           Here is some new interesting info about the FT-411:
            FT 411 OUT OF BAND MODIFICATIONS.
             ---------------------------------

 1) Open the front cover

 2) Locate the C.P.U. unit (it is located on the front cover ).

 3) Locate Jumpers 1,2,3 and 4 , These are the band setting Jumpers

  4)  Jumpers No 1,2 and 4 should be disconnected ,and Jumper No 3 should be
connected.

 5) Close the radio .

  6)  Apply  power  to the radio and turn it on. The display will initialize
with memory No 1 flashing and the frequency display will show 1.000

  7)  Now  , adjust the display to the desired lowest receive frequency When
done ,press VFO. The memory CH will now show 2 flashing .

  8)  Adjust  the display to the desired highest receive frequency When done
press VFO . The memory CH will now show 3 flashing .

  9)  Adjust  the display to the desired lowest transmit frequency When done
,press VFO. The memory CH will now show 4 flashing

 10) Now , adjust the display to the desired highest transmit frequency When
done  ,press VFO. The rig is now set for your programed band on transmit and
receive.

         COMMENTS
         -------

  1)  After  the rig was programmed to the band and you want to change it to
other  ranges you will have to open the rig again and disconnect Jumper No 3
then  to  apply  power to the radio ,turn it on again open it again ,connect
Jumper No 3 back and repeat from steps 5 .

 Any comment and other information would be appreciated.


A  few  days  back, someone requested some mods for the FT-411E portable. In
this post is some text I downloaded from a local ham BBS that told me how to
do  the  mods  to my portable. I have some receive dead zones in the 155 MHz
region,  but I can fairly well receive the weather broadcasts in the 162 MHz
region.




ft411 - ft411.4FT411

Subject: FT-411 OUT OF BAND MODIFICATIONS
Date: 08 Feb 89

 1) Open the front cover
 2) Locate the C.P.U. unit (it is located on the front cover ).
 3) Locate Jumpers 1,2,3 and 4 , These are the band setting Jumpers
 4) Jumpers No 1,2 and 4 should be disconnected ,and Jumper No 3 should
    be connected.
 5) Close the radio .
 6) Apply power to the radio and turn it on.
    The display will initialize with memory No 1 flashing and the
    frequency display will show 1.000
 7) Now , adjust the display to the desired lowest receive frequency
    When done ,press VFO.
    The memory CH will now show 2 flashing .
 8) Adjust the display to the desired highest receive frequency
    When done press VFO .
    The memory CH will now show 3 flashing .
 9) Adjust the display to the desired lowest transmit frequency
    When done ,press VFO.
    The memory CH will now show 4 flashing .
10) Now , adjust the display to the desired highest transmit frequency
    When done ,press VFO.
11) The rig is now set for your programed band on transmit and receive.
CONTINUED IN FILE FT411.4

FT411.1
Subject: FT411 MODIFICATION VIA COMPUTER

  I  was  unhappy with the FT-411's "3" mode because the frequency had to be
entered  starting  with  the  100  MHz digit, and the ARS function would not
work. I now use it in the "2" (normal) mode with the following mod.

I  used  the  "clone" mode to dump the FT-411's ram to a computer. It's 9600
baud,  1 start bit, 1 stop bit, CMOS logic. 544 bytes are dumped when the up
arrow  is  pressed. Starting with byte $211 are the upper and lower transmit
and  receive  frequencies,  stored  in  BCD. I changed these to the limits I
wanted.  My  FT-411's  upper  PLL limit is 195.4 MHz, so I used 195 MHz. The
lower  limit MUST remain set to 130 MHz (magic number) or the keyboard entry
of frequencies will start with the 1 MHz digit .VS. the 10 MHz digit. To put
the data back into ram, just press the down arrow and send the new 544 bytes
to  the  FT-411.  You  could also just clone an H.T. that has the limits you
want.  You  can  not  clone a mode "3" H.T. to a mode "2" H.T., however. The
mode is contained in the first byte, which must match.

Bill Pherigo WR0Y
Note: I have not tried or verified this, proceed at your own risk!
WA2ISEFT411.2

BID: 6495_NO8M
From: N8LKT@NO8M
Subject: FT 411 TO PACKET

FOR  THOSE  THAT  WISH  TO  CONNECT  A  FT  411  TO PACKET VIA A MFJ TNC THE
FOLLOWING  MODIFICATIONS ARE NEEDED. IN THE BLACK LEAD FROM THE TX AUDIO OUT
INSERT  A  .01-0.1UF  CAP.  IN THE RED LEAD FROM THE PTT, INSERT A 2.2K RST.
THEN  COMBINE  THESE  INTO  A COMMON SINGLE LEAD CONNECTED TO THE TIP OF THE
SMALL  MIKE  PLUG.  THE YELLOW RX AUDIO GOES TO THE TIP OF THE LARGE SPEAKER
PLUG.  AND  THE  SHIELD GOES TO THE RING OF THE LARGE PLUG. THIS INFORMATION
CAN  BE FOUND IN THE 1989 AUGUST ISSUE OF 73. PAGE 58 IT WORKES FOR ME .73'S
N8KLT@NO8M.OH.USA.NA RELAYED BY..N0KGX...GENE

FT411.3

Yaesu  has  sent out the following as an extended frequency coverage mod for
the  FT-411.  I  tried it and it works as advertised. First remove all black
screws  from  case.  Remove 4 silver screws holding the battery connector on
bottom.  Remove the 3 knobs. Carefully separate the front and back. There is
a  multiconductor  trace  between the front and back so hinge the front from
the back to keep from putting too much tension on the traces. Looking at the
board  side of the front cover there are 8 little solder pads. They are half
hidden  by  a  cover  plate  and the multiconductor trace. Pad 2 will have a
solder  connection,  the  rest  are  open. Remove the solder fro the battery
connector on bottom.

Remove  the  3  knobs.  Carefully  separate  the  front and back. There is a
multiconductor  trace between the front and back so hinge the front from the
back  to  keep  from  putting too much tension on the traces. Looking at the
board  side of the front cover there are 8 little solder pads. They are half
hidden  by  a  cover  plate  and the multiconductor trace. Pad 2 will have a
solder connection, the rest are open. Remove the solder from pad 2 and place
a solder bridge on pad 3. All other pads will be open. Close up radio.

Now when you turn on radio it will come up with 1.000 in the display. Memory
channel  should say 1. Program in the lower receive frequency. Example 1 - 4
- 1 - 0 then push VFO key. The Memory channel should go to 2. Now program in
the  upper  receive  frequency.  i.e. 1 - 6 - 5 - 0 and push VFO key. Memory
will  move to 3. Do same for lower and upper transmit frequencies. Note. The
receiver  sensitivity  falls  off  at  162.55  to  about  1 uv. The step and
repeater  offset  will  need  to  be  re-programmed also. Follow instruction
manual.

                          COMMENTS
                          --------

  1)  After  the rig was programmed to the band and you want to change it to
other  ranges you will have to open the rig again and disconnect Jumper No 3
then  to  apply  power to the radio ,turn it on again open it again ,connect
Jumper No 3 back and repeat from steps 5 .

Subject: FT-411 OUT OF BAND MODIFICATION
Date: 05 Feb 89

I  discovered  a  nice  trick  to  increase its frequency coverage. It is so
simple  that  you don't even have to open your hand held. All you have to do
is:

1. Make sure that the power switch is off.

2.  press the UP arrow and DOWN arrow together, at the same time (those keys
are  also  called  A,  and B. and they placed at the upper right side of the
keyped)

3. Keep pressing both buttons and turn the power on.

Now  you can receive 130-174Mhz, and transmit 140-150Mhz CAUTON: When you do
this  modification  the  memories can be erased. Ayhow I think it is not the
end,  and  there are some more options. If you do have some more information
about this Hand held, Please leave me a msg with it.

TO ACTIVATE PTT LOCK ON THE 411:
--TURN RADIO OFF

--PUSH  THE  6  BUTTON, HOLD IT AND TURN ON THE RIG WHILE YOUR STILL HOLDING
IT.

--NOW, PRESS FM 6, YOU SHOULD SEE "L".

--PRESS  FM  6 AGAIN, YOU SHOULD SEE "PTT"(BOTH L AND PTT WILL APPEAR IN THE
BOTTEM LEFT CORNER OF THE LCD DISPLAY.

***CONGRADULATIONS*** YOU HAVE INSTALLED PTT LOCK IN UR RIG. TO TURN IT OFF,
 JUST REPEAT THOSE STEPS.





     *================================================================*
     *    << BBS "ARACHAN" CX3VB >> - << CX3VB-6 APRS Digipeater >>   *
     *----------------------------------------------------------------*
     *   HF 7.040 Khz  VHF 145.010 Khz  AX25 CX3VB@CX3VB.CELA.URY.SA  *
     *   E-Mail cx3vb@qsl.net  -  cx3vb@amsat.org (Solo Texto plano)  *
     *----------------------------------------------------------------*
     *  Jose Maria Techera - Melo, Cerro Largo, URUGUAY, SA (GF27WO)  *
     *================================================================*
