Modifications for the Yaesu FT-2400


Picture(s) of Yaesu - FT-2400

19-07-1998 FT-2400 expanded TRX frequency range English language 
10-02-2001 Yaesu VHF mod for commercial splits English language 


 19-07-1998 add a comment 
FT-2400 expanded TRX frequency range 
  
   


Remove  the  2  allen screws holding the front panel. On the "CONTROL UNIT",
locate the Jumpers Points. JP2 must be OPEN, JP1 AND JP3 must be CLOSED with
solder.  When  JP6 is CLOSED, you can use the 1750hz tone acces for european
repeaters.

The  expanded  range is 118 to 174 mhz on the display, but work only for 140
to 174 mhz.

 
Thank to Brian Coppock for the photo. 


This modification has been read 4402 times.
 top of page
add a comment 

 
 


 10-02-2001 add a comment 
Yaesu VHF mod for commercial splits 
  
   
Author: Tom, VO1TV - tturner@thezone.net.nospam.MODIFICATION.NET


When doing emergency work, It's common for hams to use commercial repeaters,
or, more often, to have the ABILITY to use them. In our club's work with the
local  Red  Cross,  we  have  to  ensure  we  can operate on the Societies's
commercial  repeater  in  the  VHF  band. The frequencies are just above and
below  the  2 meter Ham bands. After deployment, we will use commercial gear
to  handle  comms  within  the Society, but the first critical 2 hour period
requires  fast action, so we need to anticipate the need to communicate come
what  may  on ANY frequency. That's what makes Hams so valuable in a crisis.
The  large split makes for a minor difficulty in attempting to program Yaesu
gear.  Difficulty until you try this: This mod worked on the Yaesu 2400, the
411  and  the  470.  I  suspect  it is generic for most Yaesu VHF gear. I am
indebted to Len, VO1YS for this, who tried it on yet another Yaesu rig.

Start  by setting your rig to low power and by hooking up a dummy load. This
mod  may  take several attempts, and you don't want to be slapping a 50 watt
signal  at  a  600K  offset to your served agency's allotted frequency! THAT
might bring down wrath from any number of sources !!


All  Yaesu  gear I have used has 2 buttons or functions that we will use for
this  mod:  a function button, usually labelled "f" and a button that allows
you  to  tune  within a given memory. This button puts an underscore beneath
the  memory  number. I will call it "mr", as that is its label on my 470 and
411.


Program  into  memory  the receive frequency. That is to say, the commercial
repeater  output frequency. Put in any tone encoding required as well. Store
this memory.


Set  the  repeater  offset  to display a - or + depending on which direction
your  transmit  frequency  is. Preserve that as part of the frequency memory
too.  Try not to transmit. You have just saved a commercial frequency with a
600K split at this point.


Press  the  "mr"  button  to  display  an  underscore  at the memory channel
location.


Enter  the  transmit frequency at this point. All you are doing is adjusting
the memory tuning, and we are about to lock it in.


Press  the  (f)button  for  1/2 second or until the memory channel number is
flashing.  Now,  while  the  memory  channel number is flashing, momentarily
press  and  hold  the PTT button ( press to talk ),then simultaneously press
the  (f) button again to lock your new split. This may take several tries to
get the timing right.


You  may  have  to press the "mr" button again to remove the underscore from
beneath the memory channel number.


Look for both the - and + repeater split indicators to be displayed. That is
your sign that your mod has been successful.


carefully test your new split. 
De VO1TV


This modification has been read 3579 times.
 top of page
add a comment 

 
 



Have you any tips, trick or modifications you can't find here, please send a
mail  to me. Can't you find a modification, then don't e-mail me please. All
mododification  that  i have, is listed on this site.! Have you problem with
www.mods.dk then you can visit the support page.

Start page 
 




     *================================================================*
     *    << BBS "ARACHAN" CX3VB >> - << CX3VB-6 APRS Digipeater >>   *
     *----------------------------------------------------------------*
     *   HF 7.040 Khz  VHF 145.010 Khz  AX25 CX3VB@CX3VB.CELA.URY.SA  *
     *   E-Mail cx3vb@qsl.net  -  cx3vb@amsat.org (Solo Texto plano)  *
     *----------------------------------------------------------------*
     *  Jose Maria Techera - Melo, Cerro Largo, URUGUAY, SA (GF27WO)  *
     *================================================================*

 
