Subject: YAESU FT-23R EXTENDED FREQUENCY RANGE:

"Circumcising"  the  FT-23R  is  remarkably simple. Removing one solder blob
(pad  #7,  clearly  marked,  10 o'clock position from the speaker, 9 o'clock
from  the  microprocessor) lets the radio receive and transmit from 140.0 to
163.995  MHz.  The  two  circuit  boards  with  surface-mount components are
uncluttered.  When  opening  the  radio,  be  careful  not  to lose the tiny
coil-spring  inside  the battery-release button. I haven't measured receiver
sensitivity,  nor do I know about performance in big-city RFI; the FT-23R is
considerably  more  sensitive  at  162-MHz  weather  frequencies  than is my
modified Icom IC-02AT. [source: W9MKV]

MODS FOR FT23, 73 and 211:
**************************



9600 BPS with Yaesu FT-211RH
----------------------------

RX AUDIO:
---------
On  the RX "IF UNIT" (sub board F2869104) connect the screened lead inner to
the TK10420 IC pin 9 with the outerscreen to pin 15. Caution should be taken
to solder these if soldered to the underside of the board.

TX AUDIO:
---------

On  the  rear  of  the "MAIN UNIT", a small potentiometer will be seen (peak
devia-  -tion adjust.). Unsolder the leg nearest to the rear of the set, and
connect  the  inner of the screened TX leads to this point, the outer to the
earth  plane  adjacent to this point. To ensure that the 9600 bauds modem is
terminated  in  the  required  impedance,  it  is  essential that a suitable
terminating  resistor  be placed across the screened lead inner/outer (a 560
ohm  resistor);  this  may  usefully  be  done at the FT-211RH potentiometer
connection.

No  further  adjustments need to be made to the radio. On the tested modem a
suitable  level  of  2.5  kHz deviation was achieved with one third rotation
clock- -wise of the modem TX AF level potentiometer.


YAESU FT-23R case disassembly:
------------------------------

1)  Remove the black screws from the top panel of the radio.
2)  Remove the knobs.
3)  Remove the black screws from the rear panel of the radio.
4)  Remove the battery.
5)  Remove  the  6  screws  on  the  bottom  of the radio, where the battery
attaches.
6)  CAREFULLY remove the front panel of the radio.
7) In the left of the microprocessor and battery are several printed circuit
jumpers.  The  jumpers  labeled 7, 8 and 9 are for the frequencie mods, like
explained in the following. 8) Re-assemble the radio in the reverse order of
these steps. 9) The Microprocessor will loose all what the memory contains.


YAESU FT211/23/73 band mods:
----------------------------

The  uP's  in  the FT-23/73 and the FT-211 can be set for many frequency and
memory  mode  combinations. These modes are controled by the jumpers (solder
pads)  marked 7,8 and 9 on the "CONTROL UNIT" board of either radio. Here is
a list of what is possible:

      JUMPER         FREQUENCIES
   7    8    9         COVERED

  open open  in     140 to 164 MHZ
  open  in   in     140 to 160 MHZ
   in  open  in     144 to 148 MHZ
   in   in   in     144 to 146 MHZ
  open open open    220 to 550 MHZ
  open  in  open    440 to 450 MHZ
   in  open  in      50 to 300 MHZ
   in   in  open    430 to 440 MHZ

The  FT-211  has  separate VCO's for transmit and receive and will lock over
about 38 MHZ from approx. 130 to 180 MHZ. The FT-23 has only one VCO and the
overlap-  -ping  lock  range (Xmt & Rcv) is about 25 MHZ from approx. 135 to
175  MHZ.  Don't  forget,  if  you  adjust  the  VCO  you must realign every
electronically  tuned  stage in the front-end of the radio. The transmitters
can  be  tuned for somewhat higher power output above 164 MHz but at a great
power loss at 2m.

The non-amateur (commercial) memory mode will cause these functions changes:

 1.When in the MR mode, the channel number will be displayed instead of fre-
-quency. You can toggle back to the original "amateur" mode display by pres-
-sing F<up-arrow>. Pressing F<down arrow> bring you back to commercial mode.
However,  when switching from D to MR, the display will always revert to the
commercial mode.

  2.The function of the Dot<Pri> button will be exactly reversed. That means
now  you  can  press just one button (Dot) to get into or out of the Primary
function  The  Pri funtion (in memory mode) will be indicated by a large "P"
on the left side of the display.

  3.The  only indication of low power operation is in the memory mode. A "C"
will  appear  in the upper left corner of the display (where the primary "P"
used to be). The bargraph will always read 100%.

  4.The band scan is now even more useless. The uP will painfully count from
50 to 300 MHz.


FT23/73 in packet-radio:
------------------------

If you want to work in packet-radio, open jumper 10 to dissable the battery
save.

The  topic  is increasing the functional frequency coverage of what has been
probably Yaesu's most popular handheld tranceivers.

To save manufacturing costs, Yaesu engineers designed multiple personalities
in  the  same  CPU  module  found  in  the FT-23R, FT-33R,UHF FT-73R and the
FT-2008/7008  tranceiver.  The  FT-2008/7008  tranceiver  is  the commercial
version of the Ft-x3R series.

Unique features of this mod include 

-the  just say Mao feature (**) (NO FREQUENCY READOUT: Ch 1 thru Ch 9 appear
on  your display. Great when you aren't looking and some fellow ham tries to
rip off your simplex frequency)

-the  GREAT  WHOPPER  (opens  the CPU to 50-300 Mhz or 220-550 Mhz coverage.
Full  (.100  Mhz  to 999.9995 Mhz) adjustable freq coverage available so far
only  on  the  FT-33R;this  doesn't  mean  you can actually transmit but the
Activity light goes in TX and you get a good fake RF bargraph that indicates
that you can transmit on 750 MHz. HOW TO DO IT:

0.  Contemplate  invalidating your warranty. No beginners beyond this point.
If you don't know how to solder, don't learn here. Ask an elmer to assist.

1. If you treasure your memories, write out your contents of your radio on a
piece  of  paper. When you make the changes, the CPU runs a small diagnostic
and  see  that  the  jumpers  have  been  changed.  It  will ERASE ALL PRIOR
SETTINGS.

2. Dissassemble your tranceiver.

3.  Find  the  line of solder connections running down the CPU board. GENTLY
move all wires aside so you won't melt them.

4.  Using  solder  wick and a Good low-power soldering Iron, see chart. Read
special notes for the FT-33R.

5. Rebuild radio and count your blessings.

(**)NO FREQUENCY READOUT
------------------------

Removal  of  the  solder  bridge  labeled  number  nine  will  activate  the
commercial  side  of  the CPU module. To flip to the amateur mode, you would
press  F  UP  Arrow.  To flip to the commercial mode, you would press F Down
Arrow.

+=+=+=+=+=+=+=+=+=+=+=+=+=+=+=+=+=+=+=+=+=+=+=+=+=+=+=+=+=+=+=+=+=+=
+=+=+=+=+=+=+=+=+=+=+= FT-23, FT-73R Chart =+=+=+=+=+=+=+=+=+=+=+=+=

   50 to 300 Mhz spread        220 to 550 Mhz spread
   --------------------        ---------------------

   Open bridges 8,9  Open bridges 7,8,9

+=+=+=+=+=+=+=+=+=+=+=+=+=+=+=+=+=+=+=+=+=+=+=+=+=+=+=+=+=+=+=+=+=+=
+=+=+=+=+=+=+=+=+=+=+=FT-33R Chart =+=+=+=+=+=+=+=+=+=+=+=+=+=+=+=+=

Same  chart  as above, but I wanted to add my experience of the Yaesu FT-33R
220  Mhz  radio.  When  I  removed  number  7 and then did a cold reset <see
below>,  the  CPU cleared and showed me a L and a freq. I put .100 in. Press
D/MR. Then a U appeared. I turned the VFo knob until 999.999 appeared. Press
D/MR.

I also had to reenter the Repeater Split to the proper value.

On  the  VFO, I could QSY down to those limits (using F UP/DN) and listen to
my local Channel 13 on 215.720/.660.

Yes,  216-220  Mhz  is available with this mod. Great if 216-220 is the next
220 subband.

+=+=+=+=+=+=+=+=+=+=+=+=+=+=+=+=+=+=+=+=+=+=+=+=+=+=+=+=+=+=+=+=+=+=
-NOTES-NOTES-NOTES-NOTES-NOTES-NOTES-NOTES-NOTES-NOTES-NOTES-NOTES-
+=+=+=+=+=+=+=+=+=+=+=+=+=+=+=+=+=+=+=+=+=+=+=+=+=+=+=+=+=+=+=+=+=+=

<1>  Cold  Reset  of  the  CPU  Board.  With the radio upright and your nose
pointing  at  the CPU board, look at the Lower Right Corner of the CPU chip.
You will see two parallel SMT resistors. Below them is a screw with possibly
a paper washer. To the right is a SMT device (it's a cap) with a pointed end
facing  Left.  Ground  that  point  to  the screw or to the case with a flat
screwdriver.  Awhile  doing  that,  cycle  on/off the radio to ensure a good
reset. Remove screwdriver and then reassemble radio.

Dedicated to:
 -----  the knuckleheads in Barry Electronics who said it was impossible.
 -----  Yaesu Tech Support who claimed that there are no RESET circuits
        in their radios, when their schematic diagrams say otherwise.






     *================================================================*
     *    << BBS "ARACHAN" CX3VB >> - << CX3VB-6 APRS Digipeater >>   *
     *----------------------------------------------------------------*
     *   HF 7.040 Khz  VHF 145.010 Khz  AX25 CX3VB@CX3VB.CELA.URY.SA  *
     *   E-Mail cx3vb@qsl.net  -  cx3vb@amsat.org (Solo Texto plano)  *
     *----------------------------------------------------------------*
     *  Jose Maria Techera - Melo, Cerro Largo, URUGUAY, SA (GF27WO)  *
     *================================================================*
