Yaesu FT221R repeater mod.

    UPDATING THE YAESU FT-221R 

With  the  recent  opening  of  the  2-meter  sub  band [144.5-145.5 MHz] to
repeater  operation,owners  of  some  excellent transceivers find themselves
unable   to   use  their  rigs  to  key  machines  on  the  newly  activated
channels.Notable among those radios is the Yaesu FT-221R.In order to prevent
out-of-band  operation,only  the  146.5MHz and the 1470-MHz switch positions
permit offset transmission.Yaesu engineers did not anticipate the recent FCC
ruling  and  as  manufactured,the  221R cannot work through repeaters having
inputs  below 146.0-MHz.The solution I describe below is simple and does not
mutilate  the radio.Only two short pieces of wire and one new offset crystal
are required.

 Loosen the top cover by pulling up on the four snap fasteners and carefully
pry  off  the  cover.Turn  the set upside down on the work table .Remove the
side  screws  and  slowly  lift  away the bottom shell.The four-section band
switch will be found just behind the front panel.The second band switch from
the panel is designated as S2B, the third section as S2C.

 The solder lugs of each section of the switch [from lugs 1 through 8] start
with  number  1  on  the left UNDERSIDE of the wafer [looking from the front
panel].Number  2  is  the  first  lug on the left TOPSIDE.Number 3 through 8
follow  clockwise  so  that  number 8 is on the extreme right TOPSIDE of the
wafer,as you view the switch with the set upside down.

 On the wafer S2B solder an insulated wire about 1-1/2 inches[40 mm] long to
lugs  3  and 7.Lug 3 is not wired at the factory,and lug 7 has a yellow wire
soldered  to  it.  On  S2C connect lug 3 to lug 6.Again,lug 3 is not factory
wired;  lug  6  is  solder  to  a  dark  blue  wire.  Be  very  careful,when
soldering,not to melt the insulation of surrounding wires. A helpful idea is
to  have  a  friend  use  to  small  screwdrivers  or similar instruments to
separate,and  make  a  path  through,the  jungle of wiring around the switch
while you do the soldering.

  Now  replace  the  bottom  shell. Turn the radio right-side up. Remove the
black  plastic  cover  plate over the LOCAL board and carefully pull out the
board.  Just  rock  and  lift  it  gently  out of its edge connector. Plug a
13.9666-MHz  crystal  [case  type HC-25/U ] into position 12 on the offset /
auxiliary end of the crystal strip.Do Not use socket 9.

  At  the  bottom  of  the  component side of the LOCAL board find connector
contacts 28 and 30. They are contiguous to each other. Immediately above the
contact  strips  very  carefully  solder  [ with a low heat iron ] a bonding
bridge connecting the printed conductors of 28 and 30.Then,immediately above
this solder bridge sever the pc conductor of number 30. Use a razor blade,or
X-acto  knife.Be  sure the 28 to 30 bridge remains intact. Replace the LOCAL
board in the chassis-mounted edge-connector. Screw it down tightly.

  Turn on the transceiver. Rotate the band switch to 145.0 MHz.Throw the AUX
switch  to the UP position and the RPT switch to NORM. Key the transmitter [
with  dummy load ] and adjust the trimmer capacitor of crystal 12 [ last one
on the left , looking from the front panel ] until the transmit frequency is
600  kHz  lower  then the receive frequency. Replace the plastic cover plate
over  the  LOCAL  board.  Replace  the top cover. The set should now operate
through  the  repeaters on the 144.5-to 145.5-MHz sub band... And surprise!!
You are also able to use the 221R on 1-MHz split repeaters in the 146/147MHz
"oddball"  band.  Just  turn the band switch to 146.0 MHz,the AUX toggle UP,
the  RPT  toggle  to either NORM or REV, as the occasion requires,and you've
got  1-MHz  split without the need for an additional crystal.You're actually
using  one of the factory-wired crystals as an offset rock without impairing
the normal function.

 When I ordered my crystal I also ordered The frequency I use as simplex and
that saves a lot of tuning.I ordered Mine from "Jan Crystals",They charge as
much  for  one  as they do for two.That was the reason I ordered the simplex
one NOTE: On the LOCAL board contacts at the bottom of board there will be 6
or  more  contacts  in a row then a blank and then another one .The two that
are bridged together are the last two before the blank space.The one you cut
is  next  to  the  blank  of  the  two you bridge together.I hope I have not
confused you to much .Have fun!!





     *================================================================*
     *    << BBS "ARACHAN" CX3VB >> - << CX3VB-6 APRS Digipeater >>   *
     *----------------------------------------------------------------*
     *   HF 7.040 Khz  VHF 145.010 Khz  AX25 CX3VB@CX3VB.CELA.URY.SA  *
     *   E-Mail cx3vb@qsl.net  -  cx3vb@amsat.org (Solo Texto plano)  *
     *----------------------------------------------------------------*
     *  Jose Maria Techera - Melo, Cerro Largo, URUGUAY, SA (GF27WO)  *
     *================================================================*

