This mod gives you extended transmission range on a Yeasu FT-11R.

I  have  knowlege  that  this  mod works, but take no responsibility for any
damage  it  does  to  your  radio,  the  legality  of this mod, or any other
incurred damages.

After the mod a FT-11R will have:

Recieve: 110.000-135.995 (AM)  136.000-180.000 (FM)
Transmit: 136.000-180.000 (FM)
Empty Memories and a completely reset radio

First, Remove the antenna, battery pack, and pocket clip (if installed) from
the  radio.  Then  remove the four black screws from the corners of the main
section of the radio, the two black screws from the bottom center section of
the  main  body,  and  the two silver screws from the bottom of the keyboard
section.  Now  carefully  separate  the  back and front halves of the radio,
taking  care  not  to  put  too much strain on the internal ribbon cable, or
loose  the  small metal strap holder or the battery release button. Once you
have opened the radio, carefully remove the metal plate covering the back of
the  keyboard. Then remove the "AF" pcboard by first removing the two copper
screws  in  the  middle of the board, then holding the bottom of the pcboard
and  the  mic/speaker  jacks  between  your thumb and forefinger and pulling
straight  up.  This  may  take  a  little  force,  as you are seperating two
connectors.   Once  you  have  the  "AF"  board  removed,  set  it  and  the
connector/keyboard  backplane board aside. Now look at the lower left corner
of the controller board. You should see the 8 jumpers (they are very small),
set up like this:

     Top of radio

L   A  o-o    o o E     I don't know how the jumpers relate to the
E   B  o-o    o o F     ones on the schematic, so the letters are just
F   C  o o    o/o G     for reference in this article
T   D  o-o    o o H
                       "-" means a solder jumper, and "/" means resistor

These are the functions of the jumpers that I know of:
A- Turns your radio into the euro version (TX between 144.000-146.000)
B- ?
C- ?
D- This is the important one. Gives you extened TX range
E- Turns your radio into the 440Mhz version. Not Suggested!
F- ?
G- ?
H- Same as jumper "E"

The  only  jumper that this mod deals with is "D". It currently has a solder
jumper  across  it.  Remove  the  solder across the jumper with really small
solder  wick  or a desoldering station, taking care not to touch any plastic
with  your  soldering iron. Once this solder jumper is removed, you now have
extened  tx  range. Now carefully replace the "AF" board first, and then the
connector/keyboard  backplane  board.  Take care to get the copper grounding
connector  on the side of the mic/speaker jacks well seated. Replace the two
copper  screws in the middle of the "AF" board, and the two silver screws on
the  bottom  of  the  keyboard.  Replace  the battery eject button and strap
holder, and then replace the back half of the radio.
 
Replace  all the screws, put the battery and antenna back on, and turn the
radio  on.  You should see 144.000 on the screen. Turn the radio off and the
hold  the  MHZ/\  and MHZ\/ buttons while turning the radio on. You now have
the  transmit  range between 136.000-180.000. As a suggestion, you can store
completely  different  transmit  and  recieve  frequencies  in a memory (see
manual),  so if you store a service frequency in a memory, you can program a
legal  HAM  frequency as the transmit freq. so you never accidently transmit
on an illegal frequency.

Another  neat  feature  that  I  have  found  on these radios is the "Clone"
feature.  You  can  transfer all memories from one FT-11R to another FT-11R.
First,  make  a  cable using two male stereo 1/8" connectors, and connecting
the top(gound) and middle conductors of the plugs straight through.

Don't  connect  the tip conductors together though. Plug this cable into the
earphone  jacks  of  the  two  radios, and on each radio, hold down the "FM"
button  while turining it on. You should see every character flashing on the
screen. Now, on the radio which you wish to recieve the memory contents from
the  other  radio,  press  the  MHZ\/ button. You should see "RX CLN" on the
screen.  Then  on the radio which is to send it's memory contents, press the
MHZ/\ button. "TX CLN" should appear on the screen for about 5 seconds, then
it  should  return  to the flashing screen state. The recieving radio should
now be in normal operating mode. Turn both radios off, and remove the cable.
That's  it.  This  function  overwrites  all  of  the  recieving radio's mem
contents,  and  copies everything from memories to pager codes to the status
of the light. WARNING: The instant that you hit the MHZ\/, your memories are
GONE,  even if the transfer is unsuccessful! Also, both radios must have the
same jumper settings to successfully complete the cloning process.

That's all I know for now! Have fun!





     *================================================================*
     *    << BBS "ARACHAN" CX3VB >> - << CX3VB-6 APRS Digipeater >>   *
     *----------------------------------------------------------------*
     *   HF 7.040 Khz  VHF 145.010 Khz  AX25 CX3VB@CX3VB.CELA.URY.SA  *
     *   E-Mail cx3vb@qsl.net  -  cx3vb@amsat.org (Solo Texto plano)  *
     *----------------------------------------------------------------*
     *  Jose Maria Techera - Melo, Cerro Largo, URUGUAY, SA (GF27WO)  *
     *================================================================*
