FT-920 Transmit Frequency range expand

[A] Environment
   1. Computer 286 (12MHz), MS-DOS 3.1 or later
   2. RS-232C (Straight 9 ways type) cable
   3. Software (att0274.EXE, GEN-TBL.TXT)
 
[B] Frequency expand programming procedure
   1. Connect the FT-920 and the computer using RS-232C straight
      cable
   2. Press and hold [STEP] key and [LOCK] key on the FT-920
      then Turn the power switches on.
      (Display 000000 blinking at the MSD)
   3. Type "0761161" to the pass word form ten keypad then
      press [ENT] key
      (You will hear beep sound and display back to frequency 
      as the normal operation.)
   4. Press [MENU] key (Get into MENU mode)
   5. Select "F-SS (Destina)" then [ENT]
      (Display will show the current setting)
   6. Select "OUTSIDE" rotating sub-DIAL knob for clockwise, 
      followed [ENT] key.
      (Stop blinking of "OUTSIDE" display)
   7. Press [MENU] key. (Display backs to the frequency mode.)
   8. Insure that you can not transmit on any frequency ( if you can
      stop here do not go on your systems outside table in your eprom
      is already programed, going any farther will result in damage to
      your radio.)
   9. Turn the computer switch ON.
  10. Insert the frequency expand DISK to the computer DRIVE A:\
  11. Set MS-DOS mode prompt
  12. Type "A:"
  13. Check the DISK typing "DIR".
      (att0274.EXE, GEN-TBL.TXT)
  14. Type "att0274  gen-tbl.txt") then RETURN
      (If you are connecting to the  RS-232C COM2 port so you must
      type "att0274  gen-tbl.txt  /C" then RETURN)
  15. You will see "TX Table Write Complete" when the expand 
      programming installation is completed.

YEASU FT920 

With the radio off, press[STEP] and [LOCK] (under VFO-A) and hold 
these two keys in while you turn the raido on. Now release the two keys.
Enter the following password: 0761161, then press [ENT].
Press [MENU],Rotate VFO B though the "U" settings till you get to the 
"F" Menu (F-01 F-35).

Adjustments

VR 1003 FM MIC GAIN
VR 1009 TX GAIN POWER ADJ
VR 1010 TX GAIN POWER ADJ 
VR 1011 VHF POWER SSB/FM
VR 1012 10 WATT ADJ
VR 1013 50 WATT ADJ
VR 1014 AM POWER
VR 1015 LOW POWER ADJ 1-15 WATTS
VR 1016 HF POWER SSB/FM

*AM MODULATIONS IS ADJUSTED BY THE F MENU SYSTEM

F MENU DEFAULT SETTINGS

F-01 01.10        CPU VERSION				
F-02  1.29        DSP VERSION
F-03 FIN01.19     TUNER VERSION
F-04 OFF          TUNER CLEAR
F-05 OFF          TUNER PLATE ADJUSTMENT
F-06 OFF          TUNER WRITE TO THE TUNERS MEMORY
F-07 OFF          TUNER MOVEMENT TO CENTER
F-09 237          AM MODULATION 
F-10 131          IF SHIFT CENTER SLOT
F-11 63           SSB SQL ADJUSTMENT
F-12 147          FM SQL ADJUSTMENT
F-13 89           TX GAIN 160M
F-14 71           TX GAIN 80M
F-15 63           TX GAIN 40M
F-16 61           TX GAIN 30M
F-17 73           TX GAIN 20M
F-18 80           TX GAIN 17M
F-19 75           TX GAIN 15M
F-20 74           TX GAIN 12M
F-21 77           TX GAIN 10M
F-22 88           TX GAIN  6M
F-23 TESTOFF      TESTING TX POWER OUTPUT AND ADJUSTMENT
F-24 187          ENC-NDV    CTCSS encoder narrow deviation
F-25 168          ENC-WDV    CTCSS encoder wide deviation
F-26 207          DTMFDEV    Dual Tone deviation 
F-27 0.075        LSB REC.CALL
F-28 0.075        LSB TX.CALL
F-29 0.000        LSB PROCESSOR
F-30 0.028        USB REC.CALL
F-31 0.028        USB TX.CALL
F-32 0.000        USB PROCESSOR
F-33 OUTSIDE      DESTINA (TX OUT OF BAND)'USA' DEFAULT
F-34 OFF	  JA 20W SETTING LOWER TX POWER TO 20 WATTS
F-35 970719C      SER/NUMBER	 


;-------------------------------------------------------
;
;	GEN Transmition Table			  Enable
;                                                    Tx
;-------------------------------------------------------
	00000000		;<00> 00.000.000MHz
	01800000		;<01> 01.800.000MHz  on
	54000000		;<02> 54.000.000MHz
	-1			;<03> End Max Freq.
=1A
