Yaesu FT-51R HT Mods <Imagen>November 9, 1996

DISCLAIMER: 
           PERFORM THIS PROCEDURE AT YOUR OWN RISK. THE POSTER(S) OF THIS 
           PROCEDURE ASSUME NO LIABILITY, AND THIS PROCEDURE IS POSTED FOR 
           GENERAL INFORMATION ONLY. THE FT-51R RADIO IS NOT FCC-TYPE ACCEPTED
           FOR TRANSMISSION OUTSIDE OF THE AMATEUR RADIO FREQUENCIES. THIS 
           MODIFICATION ENABLES TRANSMISSION ON FREQUENCIES OUTSIDE OF THE 
           AMATEUR RADIO BAND, AND IS LEGAL FOR THOSE INDIVIDUALS WITH MARS/CAPS
           CERTIFICATES. THIS MODIFICATION REQUIRES THE USE OF A LOW POWER FINE
           TIP SOLDERING IRON. INDIVIDUALS WHO ARE NOT EXPERIENCED WITH 
           SOLDERING OF SURFACE MOUNT TECHNOLOGY SHOULD NOT ATTEMPT THIS 
           MODIFICATION, YOU COULD RUIN YOUR RADIO. 

Modification: RX/TX 140-174 and 420-470 MHz
Mother of Mods: RX/TX approximately 60-999 MHz
Undocumented Soft-mods/Alignments through CPU

MARS/CAP Mod
Gives you rx/tx 140-174 MHz and rx/tx 420-470 MHz:

1. Remove the battery pack from the radio. 
2. Remove the four screws directly beneath the battery pack on the radio. 
3. Remove the two screws holding the contact portion of the battery compartment
4. Remove the screw and battery pack release lever. 
   (the following steps make removal of the battery holding compartment easier) 
4. Remove the four screws on the bottom portion of the back of the cabinet. 
   Carefully remove the two halves of the radio. Pay attention to the gasket as
   you are separating the cabinet. 
5. Remove the battery pack holding compartment. 

The section you will know be working with is directly underneath the battery 
pack holding compartment (behind the touch tone pad). 

6. There is a ribbon cable connected to the control board. You can leave the 
   ribbon cable attached if you're a GOOD solderer, or you can release the two
   little black levers on each side of the ribbon cable and CAREFULLY slide the
   ribbon cable out of the socket and hold it back towards the case with a 
   piece of tape. 
   Be careful not to put a bend in the ribbon cable or pierce it.
7. Locate a set of etched jumpers on the pc board. They are located adjacent to
   the bend in the ribbon cable. They are not marked, and are situated as 
   follows (o-o indicates closed, o o indicates open): 

      JP1001   o-o
                     o o JP1005
      JP1002   o o
                     o o JP1006
      JP1003   o o
                     o-o JP1007
      JP1004   o-o

8. Using solder wick or your preferred method of solder-removal, carefully 
   remove the jumper for JP1007. This enables the 134-174, 420-470 MHz 
   transmit. 
9. Reassemble the radio, remembering to reinstall the gasket, and to carefully
   reinsert the ribbon cable if you removed it from the socket, and fasten down
   the little black socket locks. 
10. Press the MHZ /\ and MHZ \/ buttons simultaneously while turning the power
    on to the radio. This enables the modification. 


Instructions for the FT-51R Full Mod for Out of Band As well as 800 MHZ

I have modified my radio to receive from 60 to 999 mhz. It will also transmit
through much of this area, but doing so is illegal!!!

Instructions: 

1.Remove battery. 
2.Remove 6 screws holding bottom cover. 
3.Remove battery latch. 
4.Loosen 4 screws holding outer case together. 
5.Remove lower cover.
6.Unfasten ribbon cable and secure with tape. 
7.There are three joints soldered on jumpers. You will remove the bottom two. 
8.Desolder lower two jumpers from jumper pad located just above where ribbon 
  cable attaches. 
9.Leave upper jumper intact: Probably for European models. 
10.Reconnect ribbon cable. 
11.Re-assemble radio. 

Hold down UP and DOWN Volume and CALL buttons while pressing power. 

The display will read "BAND 1" 

1.Hold FM key down until F key blinks. 
2.Press MHZ UP or DOWN key several times until it reads "BAND 7" 
3.Press FM key again. It will stop blinking. 
4.Press CALL button. 
5.Radio will shut off. 

Modification is now complete! 

You must now program your radio again. I suggest using R-T systems software to
keep the old frequencies. 

If you use the software you will need a template for band

7. Before the modification, upload all frequencies to a file.
   After modification load the empty radio to a file and name BAND7.
   Now open your old file. Choose "USE TEMPLATE" and choose BAND7 Send
    the date to the radio as usual. 

YAESU FT-51R Soft-Modifications - undocumented: February 1995

The new FT-51R utilizes software to control the various deeper level functions
instead of some traditional pots and electronic components. 

To access this undocumented menu: 

1. Turn on radio, and select band you want to modify.
2. Turn off the radio.
3. Simultaneously press the 2 VOLUME keys and the CALL buttons while powering
   on.
4. You're now in the soft-mods menu.
5. You'll now see the following menu choices while turning the DIAL knob: 

BAND 1 (top of menu)
IF NO 0
S-FULL84
S-1 19
SQL TH64
SQL TI4E
MOD L 25
MOD H 27 

The only soft-mod I'm familiar with so far, is to change the deviation setting
for the mike. This is done if you're dropping out of the repeater in the middle
of a QSO. 

Turn the dial until you see MOD L 25:
1. Press the FUNCTION key down for 1/2 sec. until F flashes.
2. Press the /\MHz or \/MHz to change the numerical value.
3. Press the FUNCTION key again to save this change.
4. Do the same for MOD H 27.
5. Power off. 

I'm not sure exactly what the numerical values mean, so experimenting is 
in order. 

I'm also unclear as to what the other menu items are. I believe they have
to do with squelch settings, i.e., threshold. 

I've also been told that the software can be controlled by an external computer,
by accessing the handshake via simultaneously pressing 2 and 9, and powering 
on (remember MH-29, model # of the LCD mike). I don't know what connector or 
software is needed. 

VHF Alignment
S-Meter Full-Scale Adjust(VHF) eg.,"5-FULL90"
Low-Scale S-1 Adjustment(VHF) eg.,"5-1 26"
Squelch Preset Threshold(VHF) eg.,"SQL TH6F"
Squelch Preset Tight(VHF) eg.,"SQL TI53"
TX Deviation(VHF) For A3,B3,& C3 Versions only eg.,"MOD H 24"
Tx Deviation(VHF) eg.,"MOD L 26" 

UHF Alignment
S-Meter Full-Scale Adjust(UHF) eg.,"5-FULL70"
Low-Scale S-1 Adjustment(UHF) eg.,"5-1 26
Squelch Preset Threshold(UHF) eg.,"SQL TH6F"
Squelch Preset Tight(UHF) eg.,"SQL TI53"
Tx Deviation (UHF) for A3,B3,& C3 Versions only eg.,"MOD H 24"
Tx Deviation Adjustment UHF eg.,"MOD L 26
