copied from packet: 
 Msg# TSP  Size #Rd Date/Time MsgID        From   To 
 6051 BF   2985   0 1010/0541 1631_N2EYR   W2JIA  ALL@ALLBBS 
 Sb: IC37 mods. 
 
    Here is a list, transcribed from "220 Notes", of modifications for 
    the ICOM model IC-37A. The 27A and 47A should be very similar: 
 
     "We have been using [this mod sheet] in the Southwest Coast ever 
     since the [IC-]'37 was in production. This one is the latest 
     revision. 
 
      "The design problems of the '37 are greater than ICOM would lead 
      you to believe. The [IC-]'38 has solved a great majority of the 
      '37a problems.  However, the microphone and the UHF pigtail 
      problems still remain. 
 
       "The fix for the microphone on both rigs is the same. [see 
       below] The fix for the UHF pigtail on the '38 involves removing 
       the pigtail, and installing a bulkhead chassis mount BNC 
       connector in the hole left by the pigtail assembly. Some 
       elongation of the BNC connector holes is necessary for a good 
       fit. A short coaxial jumper may then be installed from the board 
       to the connector. 
 
 "Now, here is the official Condor Connection IC-37 modification 
 sheet. 
 
 "1. To restore high-frequency receiver audio response, replace 
 C-103 on the main unit with a .0022 uf mylar capacitor (that's 
 2200 pf). 
 
  "2. To restore LOW-frequency receiver audio response, replace 
  C-106 with a .22 uf mylar capacitor. 
 
   "3. To eliminate the distortion in the transmit audio, 
   install a 4.7k ohm resistor inside the microphone case, in 
   series with the white lead coming from microphone element. 
   Once the resistor is installed, set the DTMF level pot to the 
   middle of its range (this pot is the only one inside the 
   microphone case). To complete the mod, set R88 inside the 
   radio to the desired "mike" level. 
 
    "4. To improve the receiver sensitivity, power output, SWR 
    at the radio, and reliability, remove the RG-58 pigtail and 
    the UHF connector extending from the rear of the radio. 
    Install a BNC chassis mount, screw-in connector (UG-1094/U) 
    in the hole left in the back of the radio. The new connector 
    will screw in as if the modification was done at the 
    factory. 
 
     "5. To greatly reduce chassis heating in the receive mode, 
     remove the following components: R66, R67, R68, Q32, D42, 
     and D44 in the main unit.  Install a 7808 [3-pin voltage 
     regulator] on the transmitter power amp shield behind the 
     space reserved for the optional voice synthesiser.  Thermal 
     compound is recommended. Hook the input of the 7808 to the 
     point where R67 and R68 used to connect. Hook the output of 
     the 7808, in series with a 1N4001 diode, to J14-1. The 
     cathode of the diode goes to the connector goes to  the 
     connector, and the anode goes to the 7808. 
 
       "---Mark Gilmore, WB6RHQ 
       Newbury Park, CA." 
 
        One note on the above - the 
        BNC connector mentioned for 
        the x7-series radios is sold 
        by Radio Shack as 278-105, 
        $1.39 each. 
 
Note: I haven't tried these, proceed at your own risk.  WA2ISE 
        0158z, 1390 msgs, #6500 last 
        @KD6TH-4 MailBox> 
 
 
 
