CERT Communications Team Procedures
Alinco DJ-191 Step-by-Step
Revised 08/18/2000 |
CERT Comm, Fremont, CA. |
Initial Set-up
-
Press the POWER button located in the upper-left
of the radio.
-
The MONITOR button, labeled MON,
is the lowest button on the left side of the radio. Press and hold the
MONITOR
button. The word BUSYshould appear on
the screen and static should be heard. If someone’s transmission is heard,
rotate the knob on top of the radio until only static or silence is heard.
-
The UP and DOWN keys are located
just above the display. Press the UP or DOWN
key. The letters VOL, for volume
appear on the screen. Press the UP or DOWN
key repeatedly until the static is as loud as you want the actual received
voice to be.
-
Release the MONITOR button.
-
The FUNCTION button, labeled F,
is the upper-most button on the left side of the radio. When the FUNCTION
key is pressed, the blue labels describe the keys. Press and hold the FUNCTION
button.
-
Press the UP button. The letters SQL,
for squelch, appear on the screen.
-
If you hear static, press the UP key repeatedly
until the static goes away. If you do not hear static, press the DOWN
key until you do. Then press the UP key until the static
goes away.
-
Release the FUNCTION button.
To Receive and Transmit on a Pre-programmed
Channel
-
Check to see if M is displayed.
If not, press the A key (also labeled V/M for
VFO/Memory).
-
Rotate the knob on the top right of the radio until the desired
memory number and frequency are displayed.
-
Listen. If the frequency is not being used, press the PUSH-TO-TALK
button. The PUSH-TO-TALK button is the largest button in
the center of the left side of the radio. It is labeled PTT.
Take a breath and speak slowly and distinctly across the microphone. The
microphone is located in the lower-right corner of the radio.
To Receive and Transmit on a Frequency
Not Programmed
Using Simplex
-
If a M or
C is displayed, press the A key (also labeled
V/M
for VFO/Memory).
-
If a + or –
is displayed Press and hold the FUNCTION key (the top-most
key on the left side of the radio, labeled F) and press the
2
key repeatedly until the + or –disappears.
Release the FUNCTION key.
-
Key in all six digits of the desired frequency using the
keypad. (NOTE: The last digit may be rounded up or down to the nearest
frequency
step. To change the frequency step, see the manual for the radio.)
You may also change the frequency by rotating the dial on the top of the
radio.
-
Listen. If the frequency is not being used, press the PUSH-TO-TALK
button. The PUSH-TO-TALK button is the largest button in
the center of the left side of the radio. It is labeled PTT.
Take a breath and speak slowly and distinctly across the microphone. The
microphone is located in the lower-right corner of the radio.
Using a Repeater
-
Have the following information about the repeater available:
-
Output frequency
-
If positive or negative offset is used
-
If a tone (PL) is required, and if so, the tone
frequency.
-
If a M or C
is displayed, press the A key (also labeled V/M
for VFO/Memory).
-
Key in all six digits of the repeater output frequency
using the keypad. (NOTE: The last digit may be rounded up or down to the
nearest frequency step. To change the frequency step, see
the manual for the radio.)
-
Press and hold the FUNCTION key (the top-most
key on the left side of the radio, labeled F). Press the
2
key repeatedly until either + for positive
offset
or – for negative
offset, appears.
(The 2 key is also labeled SHIFT, another name
for offset.)
-
Release the FUNCTION key.
-
The offset frequency 0.60
should be displayed. If not, rotate the knob on the top of the radio until
it is.
-
Press PUSH-TO-TALK briefly to exit ‘offset
set mode’. The PUSH-TO-TALK button, labeled PTT,
is the largest button in the center of the left side of the radio.
-
If a tone (PL) is required, press and hold the FUNCTION
button, then press the 4 key. (The 4 key is
also labeled T SQL for Tone Squelch.) Release the
Function button. A T is displayed. Rotate
the knob on top of the radio until the proper tone frequency is
displayed. Press PUSH-TO-TALK briefly to exit ‘tone set mode’.
-
Listen. If the frequency is not being used, press the PUSH-TO-TALK
button. Take a breath and speak slowly and distinctly across the microphone.
The microphone is located in the lower-right corner of the radio.