/*********************************************************************
This is an example for our Monochrome OLEDs based on SSD1306 drivers
  Pick one up today in the adafruit shop!
  ------> http://www.adafruit.com/category/63_98
This example is for a 128x64 size display using SPI to communicate
4 or 5 pins are required to interface
Adafruit invests time and resources providing this open source code,
please support Adafruit and open-source hardware by purchasing
products from Adafruit!
Written by Limor Fried/Ladyada  for Adafruit Industries.
BSD license, check license.txt for more information
All text above, and the splash screen must be included in any redistribution
*********************************************************************/

#include <SPI.h>
#include <Wire.h>
#include <Adafruit_GFX.h>
#include <Adafruit_SSD1306.h>

// If using software SPI (the default case):
#define OLED_MOSI   9
#define OLED_CLK   10
#define OLED_DC    11
#define OLED_CS    12
#define OLED_RESET 13
Adafruit_SSD1306 display(OLED_MOSI, OLED_CLK, OLED_DC, OLED_RESET, OLED_CS);

/* Uncomment this block to use hardware SPI
#define OLED_DC     6
#define OLED_CS     7
#define OLED_RESET  8
Adafruit_SSD1306 display(OLED_DC, OLED_RESET, OLED_CS);
*/

//#define NUMFLAKES 10
#define XPOS 0
#define YPOS 1
//#define DELTAY 2

//#define LOGO16_GLCD_HEIGHT 16
//#define LOGO16_GLCD_WIDTH  16
/*static const unsigned char PROGMEM logo16_glcd_bmp[] =
{ B00000000, B11000000,
  B00000001, B11000000,
  B00000001, B11000000,
  B00000011, B11100000,
  B11110011, B11100000,
  B11111110, B11111000,
  B01111110, B11111111,
  B00110011, B10011111,
  B00011111, B11111100,
  B00001101, B01110000,
  B00011011, B10100000,
  B00111111, B11100000,
  B00111111, B11110000,
  B01111100, B11110000,
  B01110000, B01110000,
  B00000000, B00110000 };*/

#if (SSD1306_LCDHEIGHT != 64)//64
#error("Height incorrect, please fix Adafruit_SSD1306.h!");
#endif

void AT_Pattern(int rad, float rot)
{
  byte n = 5;// Number of Points or sides was 7
  int x[n];
  int y[n];
  for (byte i = 0; i < n; i++)
  {
    float a = rot + i * 2 * PI / n;
    x[i] = 64 + cos(a) * rad; // 64 Horizontal Position on Screen
    y[i] = 32 + sin(a) * rad; // 32 Vertical Position on Screen
  }

  display.clearDisplay();// Clear Display

  for (byte i = 0; i < (n - 1); i++)
  {
    for (byte j = i + 1; j < n; j++)
    {
      display.drawLine(x[i], y[i], x[j], y[j], WHITE);
    }
  }
  display.display();
}

void setup()   {
  Serial.begin(9600);

  // by default, we'll generate the high voltage from the 3.3v line internally! (neat!)
  display.begin(SSD1306_SWITCHCAPVCC);
  // init done

  // Show image buffer on the display hardware.
  // Since the buffer is intialized with an Adafruit splashscreen
  // internally, this will display the splashscreen.
  //display.display();
  //delay(1000);

  // Clear the buffer.

}


void loop() {
  int nFrames = 36;//36 number of frames in animation
  for (float f = 0; f < nFrames; f++)
  {
    int rad = f * 32 / nFrames;//64 expand size 32 fills screen
    float rot = f * 2 * PI / nFrames;
    AT_Pattern( rad, rot );
  }

  for (float f = 0; f < nFrames; f++)
  {
    int rad = 32 - (f * 32 / nFrames);// 64 64 shrink size 32 fills screen
    float rot = 2 * PI - (f * 2 * PI / nFrames);
    AT_Pattern( rad, rot );
  }
}