DIAMOND RH-205 DIAMOND RH-205


 
Last採Ri上Geta BNC750, unfortunately it did Gusha 2m bands, Revenge of the first radio industry (shares) of 2m Shingurubandoroddoantena DIAMOND RH-205 launched.

ロッドエレメント 9段伸縮 Elastic rod element 9 stage
 
伸 長 Shin Hisashi : 124cm 124cm
縮 長 Length contraction : 23cm 23cm
最大径 Maximum diameter : 12mm 12mm
重 量 Weight : 90g 90g

ロッド部分はBNC750と同様に9段伸縮で、長さもほぼ同じ。 Rod portion BNC750 Like the nine-stage scale, almost the same length. 材質もたぶん同じスチールメッキ。 Maybe even the same steel-plated material. 先端部のデザインは異なっていますけど。 Design tip but are different.
ベースコイル部はスプリング構造になっていまして、引っ掛けた際の衝撃を緩和するようになっています。 Mashi Tei Division is based coil spring structure is supposed to mitigate the impact when hung. この点もBNC750と同じですが、RH-205の方が軽いのと、コイル全体がスプリングになっているため無線機のコネクタ基部への負荷が小さく感じられるため、こちらの方が安心感がありますね。 This point also BNC750 is identical, RH-205 and the light's better to look smaller load on the base of the radio connector is for the entire coil spring, you better peace of mind here I. それでもユラユラして恐いことには変わりないのですけど。 Yurayura to be afraid but I still frozen.
BNC750RHシリーズのようにロッドとコイルが分解できるようにはなっていません。 BNC750 and RH to be resolved as rods and coils series is not. コイル部分のスプリングに直結しているみたいです。 I want to direct that portion of the coil spring.

ロッドを最大に伸ばした際のSWRの底は150MHz辺りにあり、値はおよそ1.5程度になりました。 Up the rod when extended to the bottom of the SWR in the 150MHz area, the value is now about 1.5 degree. RHの名を冠するだけあって、ちょっと周波数が高めですね(笑)。 There just bears the name of RH, it is a bit higher frequency (laughs). クラニシBR-510Aアンテナアナライザで計測する分には、5/8λアンテナなので素手で触らない(アース無し)方がSWRが良くなりました。 Cluster Dandy minutes to BR-510A is measured in Antenaanaraiza, 5/8λ not touch with bare hands because the antenna (no ground) than SWR was good.
さすがに5/8λだけあって、長距離受信では他のアンテナではウンともスンとも言わない電波でも結構粘って拾ってくれます。 The only truly 5/8λ there, the other receiving antenna is a long distance makes picking up radio waves, who stayed in quite unresponsive and with Eun-Soon. その一方で、充分な信号強度がある場合はほとんどこのアンテナを使うメリットが感じられなくなりますね。 On the other hand, if there is sufficient signal strength so I could not feel most of the benefits of using this antenna. 特に変調音が良くなるわけでもありませんから(COMETのモービルアンテナSB1なんて、長さが短いクセにミョーに変調音がキレイなんですよねぇ…。積んでいる車種の相性が良いのかしら?)。 Not even from the sound does not get better, especially modulation (COMET antenna SB1 Mobil Nante, Hey I'm beautiful the sound is modulated Myo short length addictive .... I wonder if the good chemistry of the cars have had?).
ロッドを最短に縮めた場合は1/4λアンテナとして機能するようで、アース有り・150MHzでSWRは1.2程度まで落ちます。 If the rod is shortened to the shortest in 1/4λ to act as the antenna SWR is 1.2 Stock falls to the ground at about 150MHz. ロッドを約8cm(約2/3段)伸ばすと、SWRの底が145MHz付近になりました。 Rod approximately 8cm (about 2 / 3 steps) and smooth, SWR was near the bottom of 145MHz. 当然ですが、5/8λで使うよりも送受信能力は低下します。 Of course, 5/8λ than using the transmission capacity will be reduced.

2mの5/8λなら…ということで、6mバンドも試してみましたが残念ながらイマイチな感じ。 2m of the 5/8λ that if ..., 6m comment Good feeling I even tried, but unfortunately the band. 6mで使う場合は1/4λアンテナになるためアース有りの方が良好な結果となります。 6m if 1/4λ use will result in a good way to get to the antenna ground yes. SWRの底は55MHz付近。 SWR near the bottom of the 55MHz. やっぱり高めだなぁ(笑)。 Naa crowd Undoubtedly (laughs). 計測環境のせいかもしれませんけどね。 I measured it may be because of the environment.

お値段はまあまあリーズナブルで、私の場合は税込2,100円で購入できました。 Is a fairly reasonable price, if I could buy 2,100 yen including tax.
製品パッケージにはなぜか耐入力電力が明記されていません。 The product package is not clear why the input power is resistance. うーむ困ったもんだ。 How do you trouble Hmm. 構造的に電波形式F3Eで10W程度なら大丈夫じゃないかと思いますけどね、この辺は自己責任(出た! ネット上の常套句)にて。 F3E structurally radio format in the 10W, but it's not okay if you think about, this side of self-responsibility (came! Clichés on the net) at.
Antenna, but what I had been a revival version released earlier Mizuho communication?

2008年春にコメット(株)より発売されたHFマルチバンド対応のロッドアンテナです。 Comet in the spring of 2008 (shares) were released from the rod antenna is compatible with multi-band HF. HFは周波数7MHz以上に対応し、50MHz帯にも対応しています。 HF 7MHz and higher frequency, 50MHz band are also supported. ベースコイル長をショートコードにより変更することで、広い周波数範囲に対応できるようになっています。 By changing the length of the coil short code-based, it is to accommodate a wide frequency range. ショートコードによる調節は、1. Controlled by short code is 1. 無し(取説では7MHz用)、2. No (in the Operating instructions for the 7MHz), 2. 端子1(同10MHz)、3. Terminal 1 (the same 10MHz), 3. 端子2(同14MHz)、4. Terminal 2 (the same 14MHz), 4. 端子3(同21MHz)、5. Terminal 3 (the same 21MHz), 5. 端子4(同28MHz)、6. Terminal 4 (the same 28MHz), 6. 端子5(同50MHz)の6種に変更できるようになっています。 Terminal 5 (the same 50MHz) of the six species have to be changed.

ロッドエレメント 9段伸縮 Elastic rod element 9 stage
 
伸   長 Shin Hisashi : 126.3cm 126.3cm
縮   長 Length contraction : 18.7cm 18.7cm
最 大 径 Most large-diameter : 1.5cm 1.5cm
ネ ジ 径 Diameter di Ne : 9 mm 9 mm
ネジ穴深さ Screw hole depth : 15 mm 15 mm
重   量 Weight : 70 g 70 g

ベースコイル Coil based
 
全   長 Total Length : 17.4cm 17.4cm
最 大 径 Most large-diameter : 1.7cm 1.7cm (ショートコード用端子の突起は含まない) (Protrusion of the terminal short code is not included)
ネ ジ 長 Page length Ne : 8 mm 8 mm
重   量 Weight : 95 g 95 g

ロッドとコイルを接続した際の最大伸長は取説の通り約1.43m、縮長は約0.35mです。 When the maximum elongation of the connecting rod and coil as Operating instructions about 1.43m, length contraction is about 0.35m. ロッドエレメントは残念ながらステンレスではなく、たぶんスチールメッキなのではないかと思いますが…。 Unfortunately, instead of stainless steel rod element, but I think maybe at a steel plate ....
ショートコードは直径約3mm、長さ約1cmのバナナ端子でコイルをショートします。 Short code is a diameter of about 3mm, about 1cm long and short the coil terminal of bananas. 分解状態でわかるように、コードの端子の背にも接続できる開口部があるため、使用しないときにも挿しっ放しにすることができます。 As can be seen in the state of decomposition, because of the opening of the terminal can be connected to the back of the code, you can not leave even when not in use cuttings. だったら片側はコイルに固定しても良かったのでは? Dattara is good on one side of the coil can be fixed?  と思いますけどね。 But I think. なんか小さくて無くしそうだし。 It's something so small and lost.
取説には重量157gとありますが、何度量ってもショートコードを含めて170g強あります。 Operating instructions are there in 157g weight, and also including a short code may量Tsu times over 170g. 1割弱太りました? Less than 1 percent太Rimashita? (笑) (Laughs)


BNCコネクター基部は衝撃緩和のためスプリングが内蔵されており、ご覧のように若干曲げることができます。 BNC connector base has been built to ease the shock springs can bend slightly as you can see. まあ、これはこれで良いのですがアンテナに結構重量があるため、無線機をちょいと動かすだけであっちへグニャリ、こっちへフニャリ、と傾いでくれて無線機側のアンテナ端子に思わぬ負荷がかかりそうでちょっとコワいっす。 Well, this is because the antenna weight is pretty good at this, just run away and Choi Gunyari to the radio, Funyari over here, takes an unexpected load to the radio antenna terminal at me and tilted Kowai Ssu bit of that. FT-817のBNC端子は華奢ですからねぇ…。 FT-817 in the BNC from a delicate pin Hey ....

 
ショート端子 Short terminal インピーダンス Impedance
50Ω周波数 50Ω Frequency
SWR最低値 Lowest SWR
/SWR最低周波数 / SWR minimum frequency
帯域 Band
無 し And non 6.130MHz 6.130MHz 1.05 / 6.130MHz 1.05 / 6.130MHz 6.103~ 6.175MHz(SWR≦1.5) 6.103 ~ 6.175MHz (SWR ≦ 1.5)
端子1 Terminal 1 9.140MHz 9.140MHz 1.05 / 9.140MHz 1.05 / 9.140MHz 9.055~ 9.200MHz(SWR≦1.5) 9.055 ~ 9.200MHz (SWR ≦ 1.5)
端子2(*) Terminal 2 (*) 12.480MHz 12.480MHz 1.00 / 12.180MHz 1.00 / 12.180MHz 12.07~12.34 MHz(SWR≦1.5) 12.07 ~ 12.34 MHz (SWR ≦ 1.5)
端子3 Terminal 3 16.624MHz 16.624MHz 1.30 / 16.835MHz 1.30 / 16.835MHz 16.57~17.31 MHz(SWR≦2.0) 16.57 ~ 17.31 MHz (SWR ≦ 2.0)
端子4 Terminal 4 25.380MHz 25.380MHz 1.15 / 25.050MHz 1.15 / 25.050MHz 24.65~25.52 MHz(SWR≦1.5) 24.65 ~ 25.52 MHz (SWR ≦ 1.5)
端子5 Terminal 5 41.940MHz 41.940MHz
(但し60Ωが最良値) (But the best value 60Ω)
1.1 / 42.410MHz 1.1 / 42.410MHz 41.67~43.88 MHz(SWR≦1.5) 41.67 ~ 43.88 MHz (SWR ≦ 1.5)

例によって木造家屋の室内でクラニシBR-510AアンテナアナライザにM-BNC変換プラグ直結で計測したものです。 Dandy-room wooden houses cluster by the BR-510A Antenaanaraiza cases is measured in M-BNC conversion plug directly. ロッドエレメントを最大伸長とし(*:端子2のみ、なぜか計測できず先端のロッド1段分短縮して計測しています。たぶん最大伸長でのSWR最良点は11.8MHzくらい。)、アナライザの電源は乾電池、素手で持って腹アース(腹の上にアナライザを直載せ)した状態によるもの。 Rod elements and the maximum elongation (*: only two terminals, one rod tip why we can not measure the speed measured steps. Of maximum elongation is probably the best SWR point about 11.8MHz.), Power analyzer The dry, ground with bare hands abdomen (stomach placed directly on top of the analyzer) by the state. 測定条件は従来のものと統一していますが厳密なものではないですよ。 The measurement condition is exactly what it is not consistent with what has been traditional.
取説では特性について「ポータブル無線機を肩より下げた状態にて測定…」としていますが、このアンテナもアースに対する要求はシビアらしく、腹アース(イイカゲン呼称考えろ:笑)を止めるとSWRはかなり悪化しました。 Operating instructions about the characteristics of the "measured from the shoulder down in the state of portable radios ..." and is a request for this Shibiarashiku ground antennas, ground belly (Think referred Iikagen: lol) and stop the SWR Hakanari deterioration. やはり運用時は何等かのアースを考えておいた方がよろしいかと。 Still operational and when you'd better ground if you've been thinking of any kind.
この結果を見る限り、取説では24MHz帯は端子4を想定していますが上限ギリギリですね。 Judging from this result, the band is 24MHz Operating instructions are 4 terminal and it is intended to limit the last minute. 場合によっては端子3で対応するべきかも? In some cases, should be supported by three pins?

 
Band Short Terminal SWR Lowest SWR
/SWR/ SWR minimum frequency
ロッド長 Rod length ロッド伸縮目安 Night Estimated elastic rod 帯域 Band 周波数変化量 Frequency variation
40m 40m 無し No 1.05 / 7.07MHz 1.05 / 7.07MHz 79.5cm 79.5cm 4段短縮 4 shortened stage ± 35kHz(SWR≦1.5) ± 35kHz (SWR ≦ 1.5) 30kHz/cm 30kHz/cm
30m 30m 無し No 1.05 /10.14MHz 1.05 / 10.14MHz 26.0cm 26.0cm 半段伸長 Masaru Shin-stage semi ± 30kHz(SWR≦1.5) ± 30kHz (SWR ≦ 1.5) 60kHz/cm 60kHz/cm
端子1 Terminal 1 1.10 /10.12MHz 1.10 / 10.12MHz 91.5cm 91.5cm 3段短縮 Three-stage speed ± 60kHz(SWR≦1.5) ± 60kHz (SWR ≦ 1.5) 40kHz/cm 40kHz/cm
20m 20m 端子1 Terminal 1 1.20 /14.18MHz 1.20 / 14.18MHz 36.0cm 36.0cm 1段半伸長 Stage one half Takeshi Shin ± 50kHz(SWR≦1.5) ± 50kHz (SWR ≦ 1.5) 100kHz/cm 100kHz/cm
端子2 Terminal 2 1.30 /14.08MHz 1.30 / 14.08MHz 74.0cm 74.0cm 4段半短縮 4 speed semi-stage ± 80kHz(SWR≦1.5) ± 80kHz (SWR ≦ 1.5) 80kHz/cm 80kHz/cm
17m 17m 端子2 Terminal 2 1.05 /18.10MHz 1.05 / 18.10MHz 38.5cm 38.5cm 1段2/3伸長 Stage 2 / 3 Masaru Shin ±100kHz(SWR≦1.5) ± 100kHz (SWR ≦ 1.5) 100kHz/cm 100kHz/cm
端子3 Terminal 3 1.05 /18.15MHz 1.05 / 18.15MHz 103.5cm 103.5cm 2段短縮 Two-stage speed ±250kHz(SWR≦1.5) ± 250kHz (SWR ≦ 1.5) 100kHz/cm 100kHz/cm
15m 15m 端子2 Terminal 2 1.05 /21.30MHz 1.05 / 21.30MHz 18.7cm 18.7cm 最短縮 Top speed ±100kHz(SWR≦1.5) ± 100kHz (SWR ≦ 1.5) (*)150kHz/cm (*) 150kHz/cm
端子3 Terminal 3 1.05 /21.05MHz 1.05 / 21.05MHz 68.5cm 68.5cm 5段短縮 5-stage speed ±250kHz(SWR≦1.5) ± 250kHz (SWR ≦ 1.5) 200kHz/cm 200kHz/cm
12m 12m 端子3 Terminal 3 1.00 /24.90MHz 1.00 / 24.90MHz 48.0cm 48.0cm 2段半伸長 Two-stage semi Takeshi Shin ±200kHz(SWR≦1.5) ± 200kHz (SWR ≦ 1.5) 150kHz/cm 150kHz/cm
端子4 Terminal 4 1.15 /25.05MHz 1.15 / 25.05MHz 126.3cm 126.3cm 最大伸長 Maximum elongation ±400kHz(SWR≦1.5) ± 400kHz (SWR ≦ 1.5) 200kHz/cm 200kHz/cm
10m 10m 端子3 Terminal 3 1.10 /28.20MHz 1.10 / 28.20MHz 30.0cm 30.0cm 1段伸長 Stage 1 Takeshi Shin ±200kHz(SWR≦1.5) ± 200kHz (SWR ≦ 1.5) 180kHz/cm 180kHz/cm
端子4 Terminal 4 1.10 /28.30MHz 1.10 / 28.30MHz 91.5cm 91.5cm 3段短縮 Three-stage speed ±600kHz(SWR≦1.5) ± 600kHz (SWR ≦ 1.5) 250kHz/cm 250kHz/cm
6m 6m 端子5 Terminal 5 1.35 /51.00MHz 1.35 / 51.00MHz 91.5cm 91.5cm 3段短縮 Three-stage speed ±550kHz(SWR≦1.5) ± 550kHz (SWR ≦ 1.5) 450kHz/cm 450kHz/cm
FM FM 端子5 Terminal 5 1.10 /76.00MHz 1.10 / 76.00MHz 41.5cm 41.5cm 2段伸長 Two-stage Takeshi Shin ±3.1MHz(SWR≦1.5) ± 3.1MHz (SWR ≦ 1.5) 1MHz/cm 1MHz/cm
2m 2m 端子5 Terminal 5 3.25 /144.5MHz 3.25 / 144.5MHz 103.5cm 103.5cm 2段短縮 Two-stage speed    

今度は各アマチュアバンド(+FM放送帯)で使用する場合の使用端子とロッドの長さを探ってみました。 Now each amateur band (+ FM broadcast band) I tried to explore the length of the rod when you use the terminal and use. うぅ~ん、取説にある数字よりもだいぶ短いような? Brr ... - I like much less than the figures in the Operating instructions?
「ロッド伸縮目安」はだいたいこの程度ロッドを伸ばしたり縮めたりすればよいかの目安です。 "Night Estimated elastic rod" is an estimate of what do I extend or shorten the rod or roughly this level. ○段短縮とは最大に伸ばした状態から先端のロッドを何段縮めればよいかを表します。 ○ and should reduce縮Mere stage represents the stage or what unfolded on the rod tip up from the state. ○段伸長はロッドを最短に縮めた状態から何段伸ばすかを表しています。 ○ Masaru Shin stage represents the stage or anything from the state extend the shortest rod shortened.
「周波数変化量」はロッドを1cm縮めた際に、SWR最低周波数がどの程度上がったかを計測したものです。 "The amount of frequency change" is shortened when the rod 1cm, SWR is a measure of how much you have raised the minimum frequency. ただし、15mバンドの(*)はこれ以上縮められないため、1cm伸ばして周波数がどの程度下がったかを示しています。 However, 15m of the band (*) are no longer shrinking, 1cm down shows how much you stretch frequency.
なぜか20mと6mバンドの調子がイマイチでしたが、全般的には取説にあるスペックより良好な結果となりました。 20m and 6m comment Good comment was why the tone of the band in general has become more favorable results in specs Operating instructions. これは腹アース(も止メぇ)の効果が大きいようです。 This ground belly (sealing the Webmaster E) seems to have a major impact. やっぱりアースは大切なようですね。 It looks like you knew I care ground.
6mの1/4λなら…と、試しに2mバンドの底も探ってみましたが、こりゃちょっと使えそうにありませんでしたねぇ…。 6m of 1/4λ if ... and I have to try to explore the bottom of the 2m band, was not likely to be using a little Hey WTF ....

マルチバンドに対応し、なかなか便利なアンテナなのですが、ちょーと重いのが個人的にはマイナスです。 Multi-band support, the antenna is a handy, but in the heavy personalーCho is negative. 耐入力は120Wもいらないから軽量化してほしいですね。 Input resistance is 120W and I hope people do not want even lighter from. 風圧でアンテナが煽られると無線機のアンテナ端子が壊れそうでコワいんですよ。 It is broken so I Kowai the radio antenna terminal and be fueled by an antenna in the wind.
あと、高価なのがちょっとね…。 Later, it is a little expensive .... 私は税込み12,440円で買いました。 I bought at 12,440 yen including tax.