From: Tony Sweeney (firstname.lastname@example.org)
Date: Wed May 17 2000 - 17:54:49 PDT
I will send you my spice deck result plots and see if you think the SSO
noise I see is realistic and will account for the majority of RJ we see.
Thanks for your help!
Ron Miller wrote:
> I cannot agree with your precept that we cannot simulate random jitter.
> NOISE ANALYSIS
> One of the biggest contributors is thermal noise which varys the voltage
> amplitude, so at the crossover it causes jitter in the waveform. Shot noise
> and similar noise sources as well as assumed EMI received on traces can
> be estimated and added to thermal noise. I think HSPICE has a means to
> add this in. ADS does for sure.
> OTHER RANDOM JITTER SOURCES
> The clock generator has random jitter but is usually specified as phase
> and is usually ~10 ps or there about.
> Digital gates can phase modulate the signal edge, but this is usually quite
> small and is caused by amplitude variations in the ICs caused again by noise
> and also by crosstalk with other signals at the gate levels.
> These are all secondary effects and are small. Random noise is the big
> in random jitter, and can be simulated.
> Ron Miller
> > -----Original Message-----
> > From: Tony Sweeney
> > Sent: Wednesday, May 17, 2000 10:16 AM
> > To: email@example.com.Sun.COM
> > Subject: [SI-LIST] : Point to Point Timing Budget and BER
> > Calculations
> > I have been working on several point to point applications using various
> > buffers and over various transmission line length. HPSPICE is being used
> > to model:
> > Output Buffer
> > Bondwires (coupled)
> > Package Model (coupled)
> > Board Vias (lumped)
> > Transmission line (W model coupled)
> > Board Vias
> > Package
> > Bondwires
> > Input Buffer
> > On chip power distribution is modeled for a group of outputs for SSO
> > analysis
> > A seperate clock path is also modeled and simulated with the data
> > Simulations are run over process, volatage and temp corners.
> > Different pattern sets are used to evaluate SSO, and Crosstalk. The
> > cross talk pattern is modified with the middle trace getting an Pseudo
> > Random Pattern. ISI is measured at the far end.
> > In the end, eye patterns are generated and we can see the margin in
> > setup and hold times.
> > The question is: Given we cannot simulate Random Jitter, how much margin
> > do you need to garuntee a very low BER? Can you mathmatically predict
> > BER based on a deterministic Jitter Budget?
> > If you have very small margin let's say 10ps with your deterministic
> > budget, does that mean you will have a high BER?
> > --
> > Anthony C. Sweeney
> > Field Applications Engineer
> > LSI Logic Corporation
> > 7585 Ronson Road
> > San Diego, CA 92111
> > Ph: 858-467-6980
> > Fax: 858-496-0548
> > Pager: 888-961-7562
> > **** To unsubscribe from si-list or si-list-digest: send e-mail to
> > firstname.lastname@example.org. In the BODY of message put: UNSUBSCRIBE
> > si-list or UNSUBSCRIBE si-list-digest, for more help, put HELP.
> > si-list archives are accessible at http://www.qsl.net/wb6tpu
> > ****
> **** To unsubscribe from si-list or si-list-digest: send e-mail to
> email@example.com. In the BODY of message put: UNSUBSCRIBE
> si-list or UNSUBSCRIBE si-list-digest, for more help, put HELP.
> si-list archives are accessible at http://www.qsl.net/wb6tpu
-- Anthony C. Sweeney Field Applications Engineer LSI Logic Corporation 7585 Ronson Road San Diego, CA 92111 Ph: 858-467-6980 Fax: 858-496-0548 Pager: 888-961-7562
**** To unsubscribe from si-list or si-list-digest: send e-mail to firstname.lastname@example.org. In the BODY of message put: UNSUBSCRIBE si-list or UNSUBSCRIBE si-list-digest, for more help, put HELP. si-list archives are accessible at http://www.qsl.net/wb6tpu ****
This archive was generated by hypermail 2b29 : Wed Nov 22 2000 - 10:50:23 PST