Re: [SI-LIST] : Question to Jitter

About this list Date view Thread view Subject view Author view

From: Kai Peters (Kai.Peters@nsc.com)
Date: Wed Apr 11 2001 - 05:49:17 PDT


Hello Neeraj,

thanks a lot so far :-)

Cheers,
Kai

                                                                                                                    
                    neeraj.sharma
                    @wipro.com To: si-list@silab.eng.sun.com@Internet
                                         cc: (bcc: Kai Peters/Europe/NSC)
                    04/11/01 Subject: Re: [SI-LIST] : Question to Jitter
                    05:14 AM
                                                                                                                    
                                                                                                                    

Hello Kai,

Cycle to cycle jitter is the variation in the clock transition from the
corresponding transition in the previous cycle.

Another jitter definition is the periodic jitter (or the short term jitter)
that measures the maximum variation in clock transitions from ideal
position. The variations can be leading or lagging from the ideal position.

Long term jitter is the maximum change in the clock transition from ideal
position over many clock cycles. (normally can be measured using delayed
time base on the oscilloscopes). This is closest to be called the peak to
peak jitter.

More cycle to cycle jitter can add to the measured peak to peak jitter
values over a period of time. From a system point of view cycle to cycle
jitter can cause more harm. Setup and hold time failures are primarily
caused by clock period differences between the consecutive cycles rather
than the clock variations from an "ideal" clock.

Following article from Cypress and page at the Lecroy website can be of
help.

Jitter in PLL-Based Systems: Causes, Effects, and Solutions
http://www.cypress.com/pub/appnotes/jitrpll.pdf

Introduction to Jitter and Timing Analysis
http://www.lecroy.com/tm/Library/Labs/VolumeIVJitterTiming/default.asp

Regards,
Neeraj

This is an email from :
************************************************************
Neeraj Sharma
Senior Engineer - VLSI/System Design
Wipro Technologies
#72, "Keonics Electronics City"
Bangalore - 561229 India
Phone : +91-80-8520 408 ext 4163, 4164
Email : neeraj.sharma@wipro.com
Web : www.wipro.com
************************************************************

----- Original Message -----
From: Kai Peters <Kai.Peters@nsc.com>
To: si-list <si-list@silab.eng.sun.com>
Sent: Wednesday, April 11, 2001 3:34 PM
Subject: [SI-LIST] : Question to Jitter

Dear Si-list members,

I'm looking for references of jitter-definitions possibly covering questions
like
is there any relation of cycle-to-cycle- to peak-to-peak-jitter ?
P-t-P jitter could be the measured value for both random and deterministic
jitter, but where does
cycle-to-cycle belong to ?

Any hints will be appreciated

Thanks,

Kai

**** To unsubscribe from si-list or si-list-digest: send e-mail to
majordomo@silab.eng.sun.com. In the BODY of message put: UNSUBSCRIBE
si-list or UNSUBSCRIBE si-list-digest, for more help, put HELP.
si-list archives are accessible at http://www.qsl.net/wb6tpu
****

**** To unsubscribe from si-list or si-list-digest: send e-mail to
majordomo@silab.eng.sun.com. In the BODY of message put: UNSUBSCRIBE
si-list or UNSUBSCRIBE si-list-digest, for more help, put HELP.
si-list archives are accessible at http://www.qsl.net/wb6tpu
****


About this list Date view Thread view Subject view Author view

This archive was generated by hypermail 2b29 : Thu Jun 21 2001 - 10:11:31 PDT