Path: cbfsb!att!linac!uwm.edu!zaphod.mps.ohio-state.edu!wupost!m.cs.uiuc.edu!vela!argo.acs.oakland.edu!SDKUO From: sdkuo@argo.acs.oakland.edu (Steve Kuo) Newsgroups: rec.radio.amateur.misc Subject: Re: Alinco DJ-160T: DTMF decode works great, now what about mods? Message-ID: <10133@vela.acs.oakland.edu> Date: 25 Sep 91 03:25:25 GMT References: <1991Sep24.162134.5795@usenet@CS.ORST.EDU> Sender: news@vela.acs.oakland.edu Reply-To: sdkuo@argo.acs.oakland.edu Organization: Oakland University, Rochester, MI Lines: 87 In article <1991Sep24.162134.5795@usenet@CS.ORST.EDU>, youngqd@jacobs.CS.ORST.EDU (Dean Youngquist) writes: >I do a lot of boating and for that reason I would like to get the out of >band transmit mod for my Alinco DJ-160T. It sure could be a lifesaver if >I could call for help on the marine emergency channel of 160 something >MHz if my volvo outdrive quits 30 miles off shore! For this reason I >would really like to modify the rig. Here is the out-of-band-xmit mod for the DJ-160T. Steve Kuo, N8OPH, sdkuo@oakland.edu ===== starts here ===== Path: vela!umich!ox.com!caen!spool.mu.edu!agate!dog.ee.lbl.gov!ucsd!news-mail-gateway From: ds1437%BROCK1P.BITNET@cornellc.cit.cornell.edu Newsgroups: rec.radio.amateur.misc Subject: DJ-160 MODS Message-ID: <9106080531.AA20295@ucsd.edu> Date: 8 Jun 91 08:30:59 GMT Sender: daemon@ucsd.Edu Organization: UCSD Usenet Gateway Lines: 64 The new Alinco DJ-160 Radio will receive between 137-174 Mhz, and transmit in the 2Meter band only (144-148Mhz). A simple modification to the radio will enable it to transmit in the full range it receives currently. I have not tested the output power on other frequencies (Due to my one and only watt meter getting fried) however I have tried setting a weather receiver a small distance away, and I did hear the radio in the receiver. To make the mod, the following must be done: (I assume that you have some experience with electronics and that you can tell a wire from a resistor, from a transistor) 1) Take the battery of the radio by lifting the battery release button. If you look at the bottom of the radio, there will be a metal plate that is held on with 4 small screws. Take this plate off, noting exactly how the clip was held on (like the slot for the battery release clip) 2) On the back of the radio there are two screws that hold the back of the radio on, take these screws out. 3) Now you should be able to lift the bottom part of the radio by the battery release button slightly apart. I was told that you should take the top knobs off, but I found that I didn't have to. 4) If you take the Battery Release Button and turn it about 90 degress, the button should come out easily. After you get the small piece of plastic that is the button, you should see a yellow wire behind where the clip was. 5) Take a small wire cutter and CUT this YELLOW wire. You should probably make sure that the wire doesn't have bare metal showing from a lousy cutter, because I don't think that grounding this wire to the case would be HEALTHY for your radio. :-) 6) After You cut this wire. Assemble the radio, and just before you turn on the radio, do a power reset by holding the FUNC button while turning on the radio. This will reset the radio to ALL of the factory set parameters. YOU WILL LOOSE PROGRAMMED FREQUENCIES that were programmed into the memory mode of the radio, so just write the frequencies down before proceding with the above instructions. 7) The radio should be just like new, except that the transmit will be enabled for ALL frequencies! GOOD Luck! If you use these mods for ILLEGAL purposes, pity upon thy sole, for you do not belong in the ranks of Amateur Radio. This information is only supplied for Legal and Informational Purposes only and I can NOT be held responsible for anything that you do with this INFO. And if you are an idiot and screw up your radio by your own stupididy, TOO BAD. I can't be held responsible for my own actions anyhow, so as Brian@ucsd.edu would say, "So There!" **************************************************************************** Name: Donald L. Schleede Snail-Mail: Call: KB2LZF Dept. Earth Sciences E-mail Addresses: SUNY Brockport ds1437%brock1p@cornellc.cit.cornell.edu Brockport, NY 14420 dschleede@unidata.ucar.edu Twisted Pair: root@kazumi.UUCP (716) 395-5760 Planet: Earth **************************************************************************** From cbfsb!att!linac!pacific.mps.ohio-state.edu!zaphod.mps.ohio-state.edu!sdd.hp.com!spool.mu.edu!cserver!edsi!resistor Fri Sep 27 09:12:04 EDT 1991 Article: 8202 of rec.radio.amateur.misc Path: cbfsb!att!linac!pacific.mps.ohio-state.edu!zaphod.mps.ohio-state.edu!sdd.hp.com!spool.mu.edu!cserver!edsi!resistor From: resistor@edsi.plexus.COM (Mr. Resistor) Newsgroups: rec.radio.amateur.misc Subject: Re: Alinco DJ-160T: DTMF decode works great, now what about mods? Message-ID: <1991Sep27.003806.16480@edsi.plexus.COM> Date: 27 Sep 91 00:38:06 GMT References: <1991Sep24.162134.5795@usenet@CS.ORST.EDU> Organization: Enterprise Data Systems Incorporated, Appleton WI Lines: 15 youngqd@jacobs.CS.ORST.EDU (Dean Youngquist) writes: >I do a lot of boating and for that reason I would like to get the out of >band transmit mod for my Alinco DJ-160T. It sure could be a lifesaver if >I could call for help on the marine emergency channel of 160 something >MHz if my volvo outdrive quits 30 miles off shore! For this reason I >would really like to modify the rig. Take the radio apart and under the battery release button is two jumpers. Cut the yellow one. -- Jason Hanson ___/\ /\ /\ /\___ Mr. Resistor \/ \/ \/ resistor@edsi.plexus.COM Ham Radio: N9LEA Menasha, Wisconsin USA ..spool!cserver!edsi!resistor