Functions
Function | Procedure
| Transfer current memory to VFO | Func+SC
|
Transfer Call memory to VFO | Turn Selector or press Up or Down/*
|
Fast frequency dial | Func+Selector
|
VFO reset (memories retained) | Hold down Moni while powering up
|
All reset | Hold down Func+Moni while powering up
|
Change Call | Select call, Func+V/M, set frequency, Func+V/M
|
Change Call | Set freq in VFO, Func+V/M, Call, Call, Call
|
Using My key | Func+Up/*
|
Assign My key | Set, select function to assign, Func+Up/*, Set
|
Store memory | Set freq in VFO, Func+V/M, select memory, Func+V/M
|
Erase memory | Select memory, Func+Set, Func+Selector turn
|
Split mode | Set receive frequency, Set, dUP:on, SP (tx Freq), Set
|
Scanning
Scan type | Procedure
| 1MHz scan | Set frequency in VFO, SC to start, SC to end
|
Entire band | Start 1MHz scan, Func+SC to scan band
(Func+SC toggles band/MHz scan modes)
|
Program scan | Set VFO mode, Func+PS, select program #, enter
start freq using numeric keys, enter end freq
using numeric keys, SC to end entry.
To start scan, set to VFO, Func+PS, select program #,
PS to start scan, PS to pause scan, SC to end scan.
Numerics can be used while scanning to change pgm #.
To change scan range, Func+PS, select pgm #, use
Down or Up/* to select start or end freq, and numerics
to enter new frequency, SC to end.
|
Simple program scan | Set start memory in VFO, Func+SC, enter end
freq with numerics, scan starts. SC to stop
scan.
|
Erase scan range | Func+PS, select program #, Func+Set, Func+Selector, SC
|
Memory scan | Memory mode, SC to start/stop scan
|
Marked memory scan | Memory mode, select memory to mark, Set, mm:on, Set
To set scan mode, VFO mode, Set, mm:on, Set
To start scan, Memory mode, SC to start/stop scan
|
Memory block scan | Memory mode, Func+PS to select memory block, SC
To start scan, Memory mode, PS (SC to stop)
To change block range, Mem mode, Func+PS, select block,
input 3 digits as new start memory address, use Down
or Up/* to recall end memory address, input 3 digits
for new end address, SC to end
To change block during scan, use 2 digits with numerics
|
Tone Squelch Scan | Set frequency, Set, tSq:on (TSQ), CF 100.00, SC to scan
|
Keys
Keystroke | VFO Mode Function | Memory Mode Function
| L | lamp for 5 seconds
|
Func+L | lamp on continuously (until Func+L)
|
Moni | open squelch (& reverse on repeater)
|
Func+Moni | squelch open continuously (Moni cancels)
|
PTT+Moni | transmit 1750Hz tone burst
|
Call | recall/cancel the Call memory (different Call in each band)
|
Func+Call | recall/cancel the DTMF memory
|
V/M | switch to Memory mode | Switch to VFO mode
|
Func+V/M | store the memory | allows changes to the memory (also Call)
|
Band | changes bands | No function
|
SC | starts/cancels 1MHz scan | starts/cancels memory scan
|
Func+SC | sets the end frequency of program scan | transfers memory contents to VFO
|
| while scanning switches between 1MHz scan and All scan
|
PS | starts/holds program scan mode | starts block memory scan
|
Func+PS | sets range of program scan | assigns block during memory scan
|
PO/FL | selects transmitter power level (1W/0.7W high, 0.3W low)
|
Func+PO/FL | sets/cancels frequency lock
|
Set | recalls/cancells Set mode
|
Func+Set | No Function | clears the memory or a setting, program
scan range or the DTMF memory
|
Up/* | increase frequency or memory address, restarts scan upward
|
Func+Up/* | access the set mode in My key
|
Down | decrease frequency or memory address, restarts scan downward
|
Set mode functions: