Definition

[0|1] = [OFF|ON] = [DISABLE|ENABLE] = [FALSE|TRUE]

[A|B] = [Bank-A|Bank-B] = [LEFT|RIGHT]

Number as defined

Series as defined

String of characters as defined

Emulation via the serial port of a keypad input

A function/action initiated only via the serial port

Emulation via the serial port of a Menu function input

Command Syntax:
Commands may be entered in upper or lower case

Input recognized but parameters not correct

Input not recognized

Input accepted

Description

Get/Set Automatic Band Change; [OFF|ON]

APRS Bulletin Group; str = [string], 0-29 characters

Get/Set Auto Display Dim; [OFF|ON]

Get/Set Volume Setting; b = [A|B], n = 0-3F = off to full cw

Get/Set Output data to serial port; [OFF|ON]

Get/Set Advanced Intercept Point; [OFF|ON]

APRS MSG Group; str = [string], 0-59 characters

Get/Set APRS Auto Message reply; [OFF|ON]

Get/Set Auto Power Off; n = 0:OFF, 1:30 MIN, 2:60 MIN

Get/Set Position Limit; nnnn = 0000:OFF, nnnn:KM

Auto Reply Message; str = [string], 0-64 characters

Get/Set Auto Repeater Offset; [OFF|ON]

Get/Set Auto Simplex Check [A|B], [OFF|ON]

Get/Set Band TX and Control;
    0,0:[A = TX & CT]          0,1:[B = TX A = CT]
    1,0:[A = TX, B = CT]       1,1:[B = TX & CT]

Get/Set Beacon mode; [OFF|ON]

Get/Set Key Beep; [OFF|ON]

Get/Set Beep on APRS messages; 0:OFF, 1:MINE, 2:ALL NEW, 3:ALL

Get/Set [A|B] Frequency and Parameters

  xyz = ccc,fffffffffff,s,h,r,t,c,d,nn,dddd,cc,ooooooooo,a,l

 b = [0/1]---------- bank; 0:A, 1:B
 c = [001]---------- memory channel number; 001-200, L0-L9, U0-U9
 f = [00146520000]-- frequency in Hz; 11 digits
 s = [0-9]---------- frequency tuning step; (see ‘ST’ for values)
 h = [0]------------ offset direction; 0:none , 1:plus , 2:minus
 r = [0/1]---------- reverse; [OFF|ON]
 t = [0/1]---------- tone; [OFF|ON]
 c = [0/1]---------- ctcss; [OFF|ON]
 d = [0/1] --------- dcs; [OFF|ON]
 n = [00]----------- tone index; (see ‘TN’ for values)
 d = [0000]--------- dcs index; (see ‘DCSN’ for values)
 c = [00]----------- ctcss index; (see ‘CTN’ for values)
 o = [000600000]---- offset frequency in Hz; 9 digits
 a = [0/1]---------- AM/FM; 0:FM, 1:AM
 l = [0/1]---------- lockout; [OFF|ON]

Get/Set Beep Volume; n = 0:off to 7:maximum

Get Squelch value; b = [A|B], y = 0:closed, 1:open

Get/Set Channel Display Mode, [OFF|ON]

Copies current VFO values to Call Channel; ccc = channel number
    Same as C-IN key - CAUTION: This is an IMMEDIATE command

Get/Set CALL key function; 0:CALL, 1:1750 Hz tone

Get/Set LCD Contrast; nn = 00:light to 16:dark

Get/Set COM port bit rate; n = 0:9600, 1:19200, 2:38400, 3:57600

Get [A|B] Call Channel Frequency and Parameters:
Set [A|B] Call Channel Frequency and Parameters:

  xyz = b,p,fffffffffff,s,h,r,t,c,d,nn,dddd,cc,ooooooooo,a

where: p = 0

 b = [0]------------ bank; [A|B]
 p = [0]------------ main memory
 f = [00146520000]-- frequency in Hz; 11 digits
 s = [0-9]---------- frequency tuning step; (see ‘ST’ for values)
 h = [0]------------ offset direction; 0:none , 1:plus , 2:minus
 r = [0/1]---------- reverse; [OFF|ON]
 t = [0/1]---------- tone; [OFF|ON]
 c = [0/1]---------- ctcss; [OFF|ON]
 d = [0/1] --------- dcs; [OFF|ON]
 n = [00]----------- tone index; (see ‘TN’ for values)
 d = [0000]--------- dcs index; (see ‘DCSN’ for values)
 c = [00]----------- ctcss index; (see ‘CTN’ for values)
 o = [000600000]---- offset frequency in Hz; 9 digits
 a = [0/1]---------- AM/FM; 0:FM, 1:AM

where: p = 1

 b = [0]------------ bank; [A|B]
 p = [1]------------ odd-split memory
 f = [00146520000]-- frequency in Hz; 11 digits
 s = [0-9]---------- frequency tuning step; (see ‘ST’ for values)

Get/Set CTCSS Enable; [OFF|ON]

Get CTD Carrier Tone Detect; b = [A|B], y = 0:none, 1:detected

Get/Set CTCSS Tone; nn = tone value index 01-39
    See ‘TN’ for values

Get/Set Date; yy = year, mm = month, dd = day

Get/Set Data Speed; n = 0:1200, 1:9600

Get/Set DCS tone; [OFF|ON]

Get/Set DCS code index;

  index = 0010 = DCS code 023 thru 1040 = DCS code 754

    0010:023  0190:116  0370:225  0550:325  0730:452  0910:627
    0020:025  0200:122  0380:226  0560:331  0740:454  0920:631
    0030:026  0210:125  0390:243  0570:332  0750:455  0930:632
    0040:031  0220:131  0400:244  0580:343  0760:462  0940:354
    0050:032  0230:132  0410:245  0590:346  0770:464  0950:662
    0060:036  0240:134  0420:246  0600:351  0780:465  0960:664
    0070:043  0250:143  0430:251  0610:356  0790:466  0970:703
    0080:047  0260:145  0440:252  0620:364  0800:503  0980:712
    0090:051  0270:152  0450:255  0630:365  0810:506  0990:723
    0100:053  0280:155  0460:261  0640:371  0820:516  1000:731
    0110:054  0290:156  0470:263  0650:411  0830:523  1010:732
    0120:065  0300:162  0480:265  0660:412  0840:526  1020:734
    0130:071  0310:165  0490:266  0670:413  0850:532  1030:743
    0140:072  0320:172  0500:271  0680:423  0860:546  1040:754
    0150:073  0330:174  0510:274  0690:431  0870:565
    0160:074  0340:205  0520:306  0700:432  0880:606
    0170:114  0350:212  0530:311  0710:445  0890:612
    0180:115  0360:223  0540:315  0720:446  0900:624

Get/Set APRS digipeater; [OFF|ON]

Get/Set Backlight Control; n = 0:off, 1:bright to 4:dim

Get/Set Dual Band; n = 0:A or B, 1:A and B are active

Get/Set DTMF Channel memory;
    cc = channel number 00-09, n..n = up to 16 digits

Get/Set DTMF Channel Name;
    cc = channel number 00-09, str = [string] 0-8 characters

Get/Set DCD Sense; s = 0:DATA (RX) BAND, 1:A AND B BANDS

Get/Set Data Band; [A|B]

Get/Set APRS data band; n = 0:A, 1:B, 2:A-TX B-RX, 3:A-RX B-TX

Get/Set DTMF Monitor; [OFF|ON]

Get/Set APRS Data TX mode; n = 0:MANUAL, 1:PTT, 2:AUTO

Deccrement memory channel or frequency step; IMMEDIATE command

Get list of BAND limits; [FL] returns;
    00118,00135,00136,00199,00136,00174,00200,00299,00300,
    00399,00300,00399,00400,00523,00400,00469,00800,01299

Returns selected band frequency [00000000000], and step size 0-9

Get/Set Multi-Function Mode Button; n = 1:MODE1, 2:MODE2, 3:MODE3

Get/Set GPS Unit; n = 0:NOT USED, 1:NMEA, GPS 2:NMEA96

Get/Set APRS Icon; x = 0 then y = index to built in icons 0-15,
    x = 1 then y = index to APRS icon table

Get Radio ID; returns 'TM-D700'

Get/Set APRS unit of measure; n = 0:Mile, 1:km

List message number [mn] returns;

    mn,cl,dt,tm,st,lt,ln,ic,ie,mt,dt,ms,cs

 mn = [nn]----------- message number; nn = 01-40
 cl = [MYCALL-10]---- callsign
 dt = [mmdd]--------- date; mm = month, dd = day
 tm = [hhmm]--------- time; hh = hour, mm = minute
 st = [a]------------ station type; a = ascii character ??
 lt = [ttttttx]------ latitude; x = 0:N, 1:S
 ln = [nnnnnnnx]----- longitude; x = 0:E, 1:W
 ic = [0]------------ icon;
 ie = [0]------------ icon ext;
 mt = [00]----------- message type;
 dt = [000000000000]- data;
 ms = [str]---------- message;
 cs = [000000000000]- course,speed,altitude??;

Get/Set Radio Keypad Lock; n = 0:no lock, 1:transceiver keys, 2:all functions accept receive

Get/Set SSTV My Call Color; n = color
    0:BLACK  2:RED      4:GREEN  6:YELLOW
    1:BLUE   3:MAGENTA  5:CYAN   7:WHITE

Get/Set Memory Channel on band [A|B]; nnn = channel number

Get/Set Memory Channel lockout; [A|B], [OFF|ON]

Get/Set Mic Control; [OFF|ON]

Get/Set FM|AM; s = 0:FM, 1:AM (decimal point elongates D700)

Get/Set Power On Message; str = [string], 0-8 characters

Get MHZ Switch position; [OFF|ON]

Copies current VFO values to Memory Channel; ccc = channel number
    Same as M-IN key - CAUTION This is an IMMEDIATE command

Get/Set Memory Name;
    n = 001-200|L0-L9|U0-U9, str = [string] 0-8 characters

Get/Set Monitor Mode; [OFF|ON] Open/Close Squelch

Get/Set My Position; n = 1-5, xyz = ddmmmmnnDDDMMMMee

    dd = degrees latitude;          DDD = degrees longitude;
    mm = minutes latitude;           MM = minutes longitude;
    mm = decimal minutes latitude;   MM = decimal minutes longitude;
    nn = north/south; 00:N, 01:S     ee = east/west; 00:E, 01:W

Get/Set My Position Name; n = 1-5, str = [string], 0-8 characters

Get [A|B] Frequency and Parameters:
Set [A|B] Frequency and Parameters:

 xyz = r,p,ccc,fffffffffff,s,h,r,t,c,d,nn,dddd,cc,ooooooooo,a,l

where: p = 0

 r = [0]------------ required ‘0’
 p = [0]------------ main memory
 c = [001]---------- memory channel number; 001-200, L0-L9, U0-U9
 f = [00146520000]-- frequency in Hz; 11 digits
 s = [0-9]---------- frequency tuning step; (see ‘ST’ for values)
 h = [0]------------ offset direction; 0:none , 1:plus , 2:minus
 r = [0/1]---------- reverse; [OFF|ON]
 t = [0/1]---------- tone; [OFF|ON]
 c = [0/1]---------- ctcss; [OFF|ON]
 d = [0/1] --------- dcs; [OFF|ON]
 n = [00]----------- tone index; (see ‘TN’ for values)
 d = [0000]--------- dcs index; (see ‘DCSN’ for values)
 c = [00]----------- ctcss index; (see ‘CTN’ for values)
 o = [000600000]---- offset frequency in Hz; 9 digits
 a = [0/1]---------- AM/FM; 0:FM, 1:AM
 l = [0/1]---------- lockout; [OFF|ON]

where: p = 1

 r = [0]------------ required ‘0’
 p = [1]------------ odd-split memory
 c = [001]---------- memory channel number; 001-200, L0-L9, U0-U9
 f = [00146520000]-- frequency in Hz; 11 digits
 s = [0-9]---------- frequency tuning step; (see ‘ST’ for values)

Copy Memory to VFO; same as M>V key
    CAUTION This is an IMMEDIATE command

Get/Set Mute; [OFF|ON]

Get/Set APRS Callsign; str = [string], 0-9 characters

Get/Set LCD screen; s = 0:POSITIVE, 1:NEGATIVE

Get/Set Repeater Offset; nnnn = 9 full digits

Get/Set Position Ambiguity;
    n = 0:OFF, 1:1 DIGIT, 2:2 DIGITS, 3:3 DIGITS, 4:4 DIGITS

Get/Set Power Control; [A|B], n = 0:high, 1:medium, 2:low
    [PC 0] Gets Band A power setting
    [PC 1,2] Sets Band B power to low [L]

Mic Programmable Function Keys; x = key (1-4), yy = selection

    00:Power    09:MR      18:A.B.C     27:Dim
    01:A/B      10:CALL    19:M>V       28:Sub-Band Sel
    02:Monitor  11:MHz     20:M.In      29:DX
    03:Enter    12:Tone    21:C.In      30:TNC
    04:Voice    13:Rev     22:Lock      31:List
    05:1750     14:Low     23:T.Sel     32:P.Mon
    06:PM       15:Mute    24:Shift     33:BCon
    07:Menu     16:Ctrl    25:Step      34:Msg
    08:VFO      17:PM.In   26:Visual    35:Pos

Copy current settings to PM Channel ‘n’; Same as P-IN key
    CAUTION This is an IMMEDIATE command

Get/Set APRS packet speed; s = 0:1200 bps, 1:9600 bps

Get/Set Programmable Memory to n channel; n = 0:off, 1-5:channel

Get/Set Auto PM store; n = 0:ON, 1:OFF

Get/Set Position Comment; nn = selection

    00:Off Duty     05:Special     10:Custom 3
    01:Enroute      06:Priority    11:Custom 4
    02:In Service   07:Custom 0    12:Custom 5
    03:Returning    08:Custom 1    13:Custom 6
    04:Committed    09:Custom 2    14:Emergency !

Get/Set APRS Packet Path; str = [string], 0-79 characters

Get/Set Power Switch; [OFF|ON] (can only turn off)

Get/Set DTMF Transmit pause; n = 0:100 ms, 1:200 ms, 2:500 ms,
    3:750 ms, 4:1000 ms, 5:1500 ms, 6:2000 ms

Get/Set Progammable VFO; n = vfo band number,
    x = lower MHz frequency limit, y = upper MHz frequency limit

Example Default Settings:

    [PV 1,00118,00135]    [PV 4,00200,00299]    [PV 7,00400,00523]
    [PV 2,00136,00199]    [PV 5,00300,00399]    [PV 8,00400,00469]
    [PV 3,00136,00174]    [PV 6,00300,00399]    [PV 9,00800,01299]

VFO Subband selection – by active VFO A|B;
    Band ‘A’ active; 1:118, 2:144, 4:220, 6:300, 8:440
    Band ‘B’ active; 3:144, 5:300, 7:440, 9:1240

Get/Set Remote Control; [OFF|ON]

Get/Set Remote Control Answer Back; [OFF|ON]

Get/Set Remote Control Code; nnn = 000-999

Get/Set Repeater, n = 0:OFF; 1:LOCKED-BAND, 2:CROSS-BAND

Get/Set Repeater Hold; [OFF|ON]

Get/Set REVERSE mode; [OFF|ON]

Get/Set SSTV RSV Text Color; n = color
    0:BLACK  2:RED      4:GREEN  6:YELLOW
    1:BLUE   3:MAGENTA  5:CYAN   7:WHITE

Get/Set RSV message; str = [string], 0-10 characters

Set Receive Mode; This is an IMMEDIATE command

Get/Set Sky Commander Callsign; str = [string], 0-9 characters

Get/Set Scan Resume mode; n = 0:TIME, 1:CARRIER, 2:SEEK

Sky Command Transporter Callsign; str = [string], 0-9 characters

Get/Set Repeater Shift; n = 0:None, 1:minus, 2:plus

Get/Set Squelch hang time; n = 0:OFF, 1:125 ms, 2:250 ms, 3:500 ms

Get/Set Sky Command CTCSS Tone; nn = tone value index 01-39
    See ‘TN’ for values

Get Recieved signal strength on band [A|B]; nn = 00-07 ???

Get/Set SSTV Message Color; n = color
    0:BLACK  2:RED      4:GREEN  6:YELLOW
    1:BLUE   3:MAGENTA  5:CYAN   7:WHITE

Get/Set SSTV Message; str = [string], 0-9 characters

Get/Set SSTV Callsign; str = [string], 0-8 characters

Get/Set Squelch; [A|B], nn = 00:minimum to 1F:maximum

    *** WARNING THIS IS THE SYSTEM MASTER RESET ***

Get/Set Speaker Mode; n = 1:MODE1, 2:MODE2

Get S-meter squelch setting; [A|B], nn = 00:minimum to 1F:maximum

Get/Set S-Meter Squelch; [A|B], [ON|OFF]

Get/Set Frequency Step Size in kHz;
 n = 0:5, 1:6.25, 2:10, 3:12.5, 4:15, 5:20, 6:25, 7:30, 8:50, 9:100

Get/Set APRS Status Text; n = 1-5, str = [string], 0-28 characters

Get/Set Status TX Rate, every nth packet; n = 0:OFF to 8:1/8

APRS Temperature Units; 0 = F, 1 = C

TX Hold; [OFF|ON]

Get/Set Time; hh = hours, mm = minutes

Get/Set PL Tone; nn = tone value index 01-39

  01:67.0     09:91.5       17:118.8       25:156.7       33:210.7
  02:71.9     10:94.8       18:123.0       26:162.2       34:218.1
  03:74.4     11:97.4       19:127.3       27:167.9       35:225.7
  04:77.0     12:100.0      20:131.8       28:173.8       36:233.6
  05:79.7     13:103.5      21:136.5       29:179.9       37:241.8
  06:82.5     14:107.2      22:141.3       30:186.2       38:250.3
  07:85.4     15:110.9      23:146.2       31:192.8
  08:88.5     16:114.8      24:151.4       32:203.5

Get/Set TNC; n = 0:off, 1:APRS, 2:Packet

Get/Set PL Tone; [OFF|ON]

Get/Set PTT timeout, minutes; n = 0:3 min, 1:5 min, 2:10 min

Get/Set DTMF Transmission Speed; n = 0:SLOW, 1:FAST

Set Transmit Mode, [A|B] - WARNING IMMEDIATE TX

Get/Set APRS TX interval; n = 0:0.5 min, 1:1 min, 2:2 min, 3:3 min,
    4:5 min, 5:10 min, 6:20 min, 7:30 min

Get/Set Time Zone, 30 minute intervals; nn = 00-48 (-12 - +12)

UIDIGI path

Get/Set [A|B] Operating mode; n = 0:VFO, 2:MR, 3:CALL

Get/Set Use Status Message [n], n = 1-5

Increment memory channel or frequency step; IMMEDIATE mode command

Get/Set Unproto Message; str = [string], 0-9 characters
    Example: [UPR APK101]

Get/Set Band Mode; [A|B] n = 0:vfo, 2:memory, 3:call

Get [n] Programmable VFO Frequency and Parameters:
Set [n,xyz] Programmable VFO Frequency and Parameters:

 xyz = n,fffffffffff,s,h,r,t,c,d,nn,dddd,cc,ooooooooo,a

 n = [0/1]---------- VFO bank number; n = 1-9
 f = [00146520000]-- frequency in Hz; 11 digits
 s = [0-9]---------- frequency tuning step; (see ‘ST’ for values)
 h = [0]------------ offset direction; 0:none , 1:plus , 2:minus
 r = [0/1]---------- reverse; [OFF|ON]
 t = [0/1]---------- tone; [OFF|ON]
 c = [0/1]---------- ctcss; [OFF|ON]
 d = [0/1] --------- dcs; [OFF|ON]
 n = [00]----------- tone index; (see ‘TN’ for values)
 d = [0000]--------- dcs index; (see ‘DCSN’ for values)
 c = [00]----------- ctcss index; (see ‘CTN’ for values)
 o = [000600000]---- offset frequency in Hz; 9 digits
 a = [0/1]---------- AM/FM; 0:FM, 1:AM

Get/Set Visual Scan; [OFF|ON]

Visual scan output; xxx = scan step count, y = signal stregnth

Get/Set Visual Scan Mode, number of steps in scan;
    n = 1:Mode1 31 Ch, 2:Mode2 61 Ch, 3:Mode3 91 Ch, 4:Mode4 181 Ch

Get/Set Voice Synthesizer Volume; n = 0:min to 7:max?

Get/Set Waypoint Reporting format; n = 0:off,
    1:6 DIGITS NEMA     3:8 DIGITS NEMA     5:6 DIGITS MAGELLAN
    2:7 DIGITS NEMA     4:9 DIGITS NEMA     6:DGPS