My Home Brew 8/16 Meter Dual Band Vertical Antenna


The 8/16 Meter Dual Band Vertical Antenna Lower section

80/160 Vertical Lower section


The 8/16 Meter Dual Band Vertical Antenna Bottom Three Sections

Bottom Three 11 foot sections


The 8/16 Meter Dual Band Vertical Antenna Top Three Sections

Top Three 11 foot sections

The 8/16 meter antenna is constructed from six 12 foot aluminum tubes to form a slip-up mast antenna some 6 feet high.

The tubes were cleaned with paint thinner, sanded to fit well, and then lubricated with LPS. The bottom mast section is bolted to a 2 foot piece of PCV tubing, used as a base insulator and coil form. The antenna sits on a Radio Shack stainless ground mount.

The top of each tube was split with a hacksaw, then cleaned with a knife and sandpaper, then the sections are held in place with stainless steel hose clamps.

This antenna was guyed using black nylon tent cord. Before final knots were tied, the antenna was tuned to resonance at 4 khz and then the bottom stainless steel hose clamp was used to set the position. Resonance length is somewhere near 6 feet, it looks like it would be a job to measure the exact length.

I had lots of excess tubing to play with from 6 pieces of 12 foot tubing. I wanted at least a foot overlap inside each section.


Antenna Insulator and Loading Coil Form

Double PCV Tubing Coil Form

The antenna insulator is made from PVC plummers tubing. The 1-3/4 inch OD antenna mast section was mounted 5 inches inside a 2-1/2 foot piece of 2 inch OD PCV.

To strengthen the insulator, and increase the coil form size, the 2 inch PVC was inserted inside of a 2-1/2 inch, 2-1/2 foot long piece of PVC tubing. There is a slight amount of slop between the PVC tubes. To correct this a layer or 2 of black electrical tape did nicely. The antenna is secured with 2 1/4-2 stainless nuts and bolts.

The electrical connection is made with a separate stainless steel 1-38 nut and bolt stud mounted through the PVC and antenna tubes. The loading and matching coil connections are also mounted to SS 1-32 nut and bolts inserted below the antenna mast.


16 Meter Loading and Matching Coils

160 Meter Loading Coil

The 16 meter loading coil is made of roughly 38 feet of number 12 insulated copper electrical wire, close wound on a 2-1/2 inch PVC.

The turns for matching and loading may vary somewhat from one installation to another, but my settings should be close. As with any antenna, fine tuning may be required.

If you are not interested in using this antenna on 16 meters, You won't need the relays or loading coils, only a 7 turn matching coil, and then tune the length of the antenna to your favorite frequency on 8 meters.


Band Switching Relays

Coil Switching Relays

Band switching between 8 and 16 meters is accomplished by 2 high voltage single pole double through relays. A 4-conductor (2 used, 2 spare) phone wire, which runs into the shack, feeds 24 volts, supplied from a small supply at the operating desk, to switch the loading and matching coils between 8 and 16 meters.

The switching relays are mounted in a tupperware dish. Stainless 1-32 screws and nuts are used as terminal lugs. The connections to the relay are made with number 12 wire, brought through holes in the case and connected to the terminals on the outside, so the screws are not part of the circuit. After the relay boxes are installed I suggest applying clear silicone glue to all holes where wires exit. So far I haven't found any moisture build up inside.

If you can find something heaver than a tupperware box, I strongly suggest it. These first installations only lasted a year before the plastic started cracking.


The copper straps to jumper the coil and connect to the relays were reinforced with number 12 copper wire soldered on the backside. This straps were only needed to help support the relay boxes, you could use number 12 copper wire for all connections.


These high voltage relays may be hard to find. I found these in a surplus electronics store here in St. Louis. I got them for $5 each so I bought 2 spare ones.

The model is Magnacraft W158HVX-1. If a 12 volt relay could be found there would be no need for building a separate 24 volt supply.


16 Meter Loading and Matching Coils

Loading and Matching Coil

The 5 ohm feed line has it's shield connected to earth ground, and the hot conductor (center) to the lower matching relay center arm. The loading/matching coil bottom or cold side, is also connected to earth ground.

The Antenna feed point is connected to the upper loading relay center arm. When both relays are in the normally closed position, (no power supplied) the antenna is in the 8 meter position. The upper relay closed contact is connected to a tap at 11 turns from ground (8 meter loading), and the lower relay closed contact is connected to a tap 7 turns from ground (8 meter matching).

With 24 vdc applied to the relays, the antenna switches to the 16 meter band. The upper relay open contact is connected to a tap at 46 turns from ground (16 meter loading), and the lower relay open contact is connected to a tap 8 turns from ground (16 meter matching). The antenna loading/matching coils supply a DC ground on the antenna for static and lightning discharge.


The ground system and ground plane, consists of a 4 foot ground rod, driven into the earth, at the antenna base, as well as two 6 feet, and one 12 foot pieces of number 12 insulated wire, laid on top of the ground, and stretched away in any direction possible. At least one piece of ground wire is required for proper matching, the more the better. I also ran a ground wire into the basement and connected it to the cold water pipe. The matching coil, for 16 meters, also serves as a DC ground on the antenna. Rule of thumb on grounding. "YOU CAN"T GET ENOUPH GROUNDS"


Notes about construction

I suggest that when raising the mast sections that you guy the first 12 foot with steel guy wire for extra support until the antenna is somewhat supported at 6 feet.

I put 4 sets of guys on my antenna, one on each section, top free standing. I got fancy, and cut 5 each guy brackets from a piece of 1/8 inch thick alluminum rack panel. I made them square and cut a center hole in each to nicely fit each expanding mast section.

Then I drilled 4 each 1/4 inch holes in each corner for the 1/8 inch Nylon guy twine. You could also tie the guys around a hose clamp for each section, but you would have to jockey with this while raising the antenna. I had all guys in place when I started raising the sections.

You must raise the antenna on a calm day, very slowly, keeping the antenna straight as possible. It will free stand at 6 feet if you tie the bottom steel guys secure, and tight, and have the antenna insulator sitting around a radio shack mast support or some sort of ground stake to secure the antenna base from moving sideways.

I left about 5 inches of the metal steak sticking out of the ground, no more though as it will interfere with the coils. After raising the sections, lightly tie off each guy by itself, they will be permanently secured after tuning.

Finally, remove the steel guy wire in order to tune the antenna. Be sure to have help when raising this antenna. Although I did it by myself, I have had a lot of experience with slip up masts. What ever you do-

"DON'T ATTEMP THIS NEAR POWER LINES".


Notes about tuning

I suggest that after raising the mast sections, and removing the supporting steel guy wire at the 12 foot level, you connect the RF feed cable shield to ground, and the center conductor to the first 7 turn tap on the loading coil.

Disable any other connections to the coil, and install a jumper wire from the antenna feed to the 7 turn tap. You should now have only the 7 turn matching coil and the 6 foot antenna in the circuit.

Tune your radio close to 4 mhz, and then fine tune your antenna for the lowest VSWR by adjusting the second antenna section up and down inside the first.

You will have to do this in small steps, loosing all but the bottom guys slightly for each test. When the antenna is tuned, complete vertical alignment of the antenna, and secure the nylon guys.

Next, fine adjustment is done first by tuning your transmitter to your favorite 8 meter frequency, and adjusting the amount of turns, and spacing of them, on the 3 turn coil for 8 meters.

Next, fine adjust the 35 turn coil for 16 meters on your favorite frequency.

You must tune the 8 meter coil first as it is part of the 16 meter coil.


Personal commits about this antenna

This antenna performs quite well on 8 meters, much better than the Alpha Delta DX-CC, 82 foot loaded dipole, I was using. The 16 meter portion of the antenna is a plus for me, because I wasn't able to get on that band before with no room here, not even for a loaded 16 meter dipole.

I have been getting good reports from as far as Florida on 16 meters, and without a tuner, I can spread most of the phone band on 8 meters. I can spread 1 Khz on 16 meters. With the tuner in my Yaesu FT92, I can spread the whole band on 8 or 16 meters.


My next experiment with this antenna might be to try a LDG remote antenna tuner at the base. This antenna may perform well on 4 or higher. I don't like tuners in the shack, but a remote tuner might be just fine.


This is a note dated about a year after building the 16/8 meter vertical.

I tried the LDG remote tuner. It would not work at all. It would only tune a few frequencies. I sold it and purchased a SGC-23 tuner. It cost twice as much, but it tunes this antenna to all the bands just fine.

There is more information about the SGC-23 upgrade in my 8/16 upgraded to 1/16 meter antenna section.


Click here to return to my ham radio construction projects

 Click here to return to my home page