|
|
MORSE CODE-T
CODET 20
Learning MORSE CODE will require you to use a shareware program called "Code-T".
If you don't have any other similar program in your computer, then it is recommended that you download this file to
your disk. But before you do that, please try to read first and understand the following.
PURPOSE: CODE - T is a Morse Code Tutor program, designed to help
all those interested to learn to receive the Morse Code and
pass their Amateur Radio code test.
This Program is Shareware and can be used in this version for as
long as desired. There is no mandatory registration required.
The program can and should be freely distributed to all interested
in learning the Morse Code.
That is, you can copy it, use it, and share it (including
distribution at hamfests or ham radio and computer equipment
swapmeet) so long as you do not charge any money for it other than
the cost of the disk or other transfer medium, not to exceed $2.
You may not make a profit or recover labor costs for copying or
distributing this program. Code Practice must be distributed in its
original form and content.
GETTING STARTED
A. Equipment and System Requirements and Limitations
1. General Requirements
Computer: IBM PC or higher compatible
Memory: 250K
Drive : Floppy disk or hard drive
Video : Monochrome or color
B. Distribution Files
Code Practice is normally shipped un-compressed, containing
all the files necessary for operation. If you would like to give
a copy of Code Practice to a friend or want to upload it to a
computer bulletin board system, please upload a complete set of the
file in a compressed format. Do not add or remove files, since
that can create confusion to other users.
Code Practice contains the following files:
CODET.EXE - Main executable program
CODET.DOC - Codet Read Me Document
INSTALL.BAT - Installs program on to your hard drive
FILE.DIZ - DESCRIPTION FILE FOR BBS
README.BAT - Batch file to read the codep.doc file.
C. Installation
Code-T will run from floppy disk. If you receive
the program in a ZIP or other compressed form,
simply uncompress it, on the same disk or, in the
same sub-directory. A batch file name INSTALL.BAT
is included with the program that will create and
copy all files to your hard drive into a sub-
directory named CODET. Type README.BAT to read
CODET.DOC for additional instructions.
In the following examples "ENTER" means to press the key
labelled "ENTER" or "RETURN".
1. If you have a hard disk
a. Place the floppy disk in floppy drive A or B. Make that
drive the active drive type A: or B:.
b. Run the install program as follows:
A:\> INSTALL A C or b:\> INSTALL B C
(if you want to install the program on your C drive.)
2. If you have a floppy drive
a. Place the floppy disk in drive A: or B;
b. Run the program as follows:
A> CODET
or
b> CODET
Write protect the floppy to prevent the program from being altered
CODE-T BASICS
A. Starting and Quitting Code-T
To start the program:
1. At the prompt type CODET .
2. The title screen and then the main menu will appear
prompt you to enter A-L or Q to quit.
3. Start by reading the INTRODUCTION.
4. Continue thur each lesson. Don't rush! Spend about 15 to 30
minutes each day study a lesson.
5. Be sure to take time to practice each lesson and also all the
characters you have learned using menu selections "C" and "D"
of each lesson memu.
To quit:
1. At the end of the practice the screen will prompt to
to retrun to the main menu. Press "Q" to return to the Main MENU
then press Q again to end the program.
CODE SPEED DEFINITION
1. Speed Standards
a. Character, and Word Speeds.
Normally, the spacing between characters is sent at the
same speed as the character elements. However, when the
Farnsworth method is used, the spacing between
characters is sent at a slower speed than the characters
themselves. CODE-T provides a teaching method to help
you learn the code by using a modified version of the
Farnsworth method. Code-T sends all letters at a code speed
of 13 words per minute. The space between each characters
is at a rate equal to 5 words per minute.
The method will help the average student to learn the
code in less time than use code tape and record that
send code at a continuous 5 WPM or 13 WPM.
CALIBRATION
This version of Code-T does not allow the use to alter the
speed of the code. However the program is designed to produce the
same results on any computer.
DOWNLOAD
Okay, you have finished reading the preliminary instructions.
Click here to download the compressed
file of codet20 (File Name: codet20.zip; Size: 33 KB). More instructions to guide you on your Morse Code Practice
are available in Code-T.
_ _. _ _ _ _ _ _ _ .. _._ .._ _._. _._
|
COLOR CODE CONVERTOR |
|
COLOR CODE CONVERTOR: How can the value of a resistor be worked out from the colours of the bands?
The Color Code Convertor Program is a free shareware program that helps to calculate a suitable value for resistors.
Download Now!
|
|
|
Vote For This Site!
|
Back to Top
|
|
|
